From: Skinner, Stephen (Stephen.Skinner@rbs.co.uk)
Date: Tue Oct 24 2006 - 13:58:39 ART
Gents
Please could I have a helping hand .
I am trying to config pim bsr but with no luck
Cat1 - ethernet- R2 -multpointsub - r1 - ethernet - cat2
Ip 227.7.7.7 is on cat2
BSR RP is on R1
When I ping 227 from below I get this response
r1 ok
Cat1 ok
R2 . Nope.
Can someone please enlighten me .
I would have thought that if CAT1 which is behind R" can ping it , then R2
should be able to ping it ????
the BSR is seen by all devices
Pim neibhours is ok
R2#sh ip pim neighbor
PIM Neighbor Table
Mode: B - Bidir Capable, DR - Designated Router, N - Default DR Priority,
S - State Refresh Capable
Neighbor Interface Uptime/Expires Ver DR
Address Prio/Mode
30.10.1.10 FastEthernet0/0 00:23:17/00:01:35 v2 1 / DR S
25.10.1.1 Serial0/0.1 00:42:30/00:01:38 v2 1 / S
R2#
R2#sh ip mroute
IP Multicast Routing Table
Flags: D - Dense, S - Sparse, B - Bidir Group, s - SSM Group, C - Connected,
L - Local, P - Pruned, R - RP-bit set, F - Register flag,
T - SPT-bit set, J - Join SPT, M - MSDP created entry,
X - Proxy Join Timer Running, A - Candidate for MSDP Advertisement,
U - URD, I - Received Source Specific Host Report,
Z - Multicast Tunnel, z - MDT-data group sender,
Y - Joined MDT-data group, y - Sending to MDT-data group
Outgoing interface flags: H - Hardware switched, A - Assert winner
Timers: Uptime/Expires
Interface state: Interface, Next-Hop or VCD, State/Mode
(*, 227.7.7.7), 00:07:28/stopped, RP 1.1.1.1, flags: SPF
Incoming interface: Serial0/0.1, RPF nbr 25.10.1.1
Outgoing interface list: Null
(25.10.1.1, 227.7.7.7), 00:01:51/00:01:11, flags: PFT
Incoming interface: Serial0/0.1, RPF nbr 25.10.1.1
Outgoing interface list: Null
(30.10.1.10, 227.7.7.7), 00:00:09/00:03:20, flags: T
Incoming interface: FastEthernet0/0, RPF nbr 0.0.0.0
Outgoing interface list:
Serial0/0.1, Forward/Sparse, 00:00:10/00:03:19
(40.10.1.1, 227.7.7.7), 00:00:10/00:03:19, flags:
Incoming interface: FastEthernet0/0, RPF nbr 30.10.1.10
Outgoing interface list:
Serial0/0.1, Forward/Sparse, 00:00:10/00:03:19
(*, 224.0.1.40), 00:07:39/00:02:42, RP 0.0.0.0, flags: DCL
Incoming interface: Null, RPF nbr 0.0.0.0
Outgoing interface list:
Serial0/0.1, Forward/Sparse, 00:07:39/00:02:42
TIA
Stephen Skinner
The Royal Bank of Scotland plc, Registered in Scotland No. 90312. Registered Office: 36 St Andrew Square, Edinburgh EH2 2YB
Authorised and regulated by the Financial Services Authority.
This e-mail message is confidential and for use by the addressee only. If the message is received by anyone other than the addressee, please return the message to the sender by replying to it and then delete the message from your computer. Internet e-mails are not necessarily secure. The Royal Bank of Scotland plc does not accept responsibility for changes made to this message after it was sent.
Whilst all reasonable care has been taken to avoid the transmission of viruses, it is the responsibility of the recipient to ensure that the onward transmission, opening or use of this message and any attachments will not adversely affect its systems or data. No responsibility is accepted by The Royal Bank of Scotland plc in this regard and the recipient should carry out such virus and other checks as it considers appropriate.
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:06 ART