From: Povarenkin, Igor (ipov@amt.ru)
Date: Thu Oct 12 2006 - 12:16:53 ART
Thank you Brian for your answer,
In this simple scheme we have only two routing domains:
(EIGRP domain) f0/0 [Router] s0/0 (RIP domain)
Which metirc parameters I need to use?:)
From f0/0 OR s0/0?
> -----Original Message-----
> From: Brian McGahan [mailto:bmcgahan@internetworkexpert.com]
> Sent: Thursday, October 12, 2006 3:59 PM
> To: Povarenkin, Igor; Alexei Monastyrnyi
> Cc: Cisco certification
> Subject: RE: Redistribution into EIGRP
>
> Unless you have multiple exit points between the different
> protocol domains the routing metric is arbitrary. The reason why is
> that if prefix X is only reachable through exit point A then
> the metric through A is irrelevant; anyone wanting to reach prefix X
must go
> through A.
>
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of
> > Povarenkin, Igor
> > Sent: Wednesday, October 11, 2006 11:53 PM
> > To: Alexei Monastyrnyi
> > Cc: Cisco certification
> > Subject: RE: Redistribution into EIGRP
> >
> > Hello GS,
> >
> > From which interface I need to use the "bandwidth delay reliability
> > loading mtu"
> > parameters?
> >
> > For example:
> >
> > (EIGRP domain) f0/0 [Router] s0/0 (RIP domain)
> >
> > Router# router eigrp 1
> > redistribute rip metric 100000 100 255 1 1500
> > OR
> > redistribute rip metric 1544 2000 255 1 1500
> > ?
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> > > Behalf Of david robin
> > > Sent: Wednesday, October 11, 2006 5:02 PM
> > > To: Mohamed Saeed
> > > Cc: ccielab@groupstudy.com
> > > Subject: Re: Redistribution into EIGRP
> > >
> > > you can use redustribute ospf 1
> > >
> > > with setting metrics
> > > but use with it
> > >
> > > Router(config-router)# *default-metric* *bandwidth delay
> > > reliability loading
> > > mtu *
> > > as you must set a default metric for the distributed routes
> > > or configure
> > > them manulay
> > >
> > > best regards,
> > >
> > >
> > >
> > > On 10/11/06, Mohamed Saeed <mohamed_saeed2@rayacorp.com> wrote:
> > > >
> > > > Hi All,
> > > >
> > > >
> > > >
> > > > When redistributing from any IGP into EIGRP, should you
> > > manually set the
> > > > metric?
> > > >
> > > >
> > > >
> > > > Example:
> > > >
> > > >
> > > >
> > > > router eigrp 10
> > > >
> > > > redistribute ospf 1 metric 10000 100 255 1 1500
> > > >
> > > >
> > > >
> > > > Actually, I have tried to redistribute without specifying
> > > the metric but
> > > > I got improper operation and I do not know why. Has
> > > somebody encountered
> > > > this?
> > > >
> > > >
> > > >
> > > > Regards
> > > >
> > > > Mohamed Saeed, CCNP - CCIP
> > > >
> > > >
> > > ______________________________________________________________
> > > _________
> > > > Subscription information may be found at:
> > > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > > ______________________________________________________________
> > > _________
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> ______________________________________________________________
> _________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Nov 01 2006 - 07:29:05 ART