From: Brian Dennis (bdennis@internetworkexpert.com)
Date: Fri Sep 01 2006 - 14:02:39 ART
You actually show a neighbor on R2 to R1 across the PPPoFR link but you
don't have a network statement for the PPPoFR link on R2. Can you send
a show ip ospf interface from R2?
router ospf 1
router-id 2.2.2.2
area 10 virtual-link 1.1.1.1
network 2.2.2.2 0.0.0.0 area 10
network 192.1.24.2 0.0.0.0 area 24
!
R2#sh ip osp nei
Neighbor ID Pri State Dead Time Address Interface
1.1.1.1 0 FULL/ - 00:00:30 172.16.1.5
Virtual-Access1
3.3.3.3 1 FULL/DR 00:00:35 192.1.24.5
FastEthernet0/0
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Brian Dennis
Sent: Friday, September 01, 2006 9:36 AM
To: beatccielab; ccielab@groupstudy.com
Subject: RE: Virtual Link
On R6 you do not have OSPF enabled on the PPPoFR connection.
router ospf 1
router-id 2.2.2.2
area 10 virtual-link 1.1.1.1
network 2.2.2.2 0.0.0.0 area 10
network 192.1.24.2 0.0.0.0 area 24
You should always check to ensure that the OSPF neighbors have formed
BEFORE configuring a virtual link.
1) Bring up the link
2) Ping across the link
3) Enable OSPF on the link
4) Verify the OSPF neighbors
5) Configure the OSPF virtual link
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
beatccielab
Sent: Friday, September 01, 2006 8:25 AM
To: ccielab@groupstudy.com
Subject: Virtual Link
Hi all,
I have problem with my configuration OSPF virtual link over ppp over
frame relay..
Configuration Scenario like this :
area 0 ---R5--- FRS/area10 --- R2--- area24 ---Cat1
my case say: R2 not use subinterface..
i already configure like this :
R5:
interface Serial0/1/0
no ip address
encapsulation frame-relay
frame-relay interface-dlci 501 ppp Virtual-Template1 no frame-relay
inverse-arp !
interface Virtual-Template1
ip address 172.16.1.5 255.255.255.0
router ospf 1
router-id 1.1.1.1
area 10 virtual-link 2.2.2.2
network 1.1.1.1 0.0.0.0 area 10
network 172.16.1.5 0.0.0.0 area 10
R5#sh ip os nei
Neighbor ID Pri State Dead Time Address
Interface
2.2.2.2 0 FULL/ - 00:00:38 172.16.1.6
Virtual-Access1
R5#sh ip os vi
Virtual Link OSPF_VL0 to router 2.2.2.2 is down
Run as demand circuit
DoNotAge LSA allowed.
Transit area 5, Cost of using 65535
Transmit Delay is 1 sec, State DOWN,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
R6:
interface Serial0/1/0
no ip address
encapsulation frame-relay
frame-relay interface-dlci 105 ppp Virtual-Template1 no frame-relay
inverse-arp !
interface Virtual-Template1
ip address 172.16.1.6 255.255.255.0
!
interface FastEthernet0/0
no ip address
!
interface FastEthernet0/0.24
encapsulation dot1Q 24
ip address 192.1.24.2 255.255.255.0
!
router ospf 1
router-id 2.2.2.2
area 10 virtual-link 1.1.1.1
network 2.2.2.2 0.0.0.0 area 10
network 192.1.24.2 0.0.0.0 area 24
!
R2#sh ip os vir
Virtual Link OSPF_VL0 to router 1.1.1.1 is down
Run as demand circuit
DoNotAge LSA allowed.
Transit area 5, Cost of using 65535
Transmit Delay is 1 sec, State DOWN,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
R2#sh ip osp nei
Neighbor ID Pri State Dead Time Address
Interface
1.1.1.1 0 FULL/ - 00:00:30 172.16.1.5
Virtual-Access1
3.3.3.3 1 FULL/DR 00:00:35 192.1.24.5
FastEthernet0/0.
Cat1
interface FastEthernet0/1
switchport trunk encapsulation dot1q
switchport trunk allowed vlan 24
switchport mode trunk
interface Loopback0
ip address 3.3.3.3 255.255.255.0
interface Vlan13
ip address 192.1.24.5 255.255.255.0
router ospf 1
router-id 3.3.3.3
log-adjacency-changes
network 3.3.3.3 0.0.0.0 area 24
network 198.1.24.5 0.0.0.0 area 24
If issued show ip ospf virtual always down whereas if we issued sh ip
ospf nei the router another site appears...
Please advice me how to fix it this problem...
Regards,
beatccielab
This archive was generated by hypermail 2.1.4 : Sun Oct 01 2006 - 16:55:39 ART