From: Aamir Aziz (aamiraz77@gmail.com)
Date: Fri Sep 01 2006 - 10:41:52 ART
Hi,
This is the output:
R5#sh ip ospf interface s0/0.235
Serial0/0.235 is up, line protocol is up
Internet Address 1.1.235.5/24, Area 0
Process ID 1, Router ID 1.1.5.5, Network Type NON_BROADCAST, Cost: 64
Transmit Delay is 1 sec, State DR, Priority 1
Designated Router (ID) 1.1.5.5, Interface address 1.1.235.5
Backup Designated router (ID) 1.1.3.3, Interface address 1.1.235.3
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5
oob-resync timeout 120
Hello due in 00:00:09
Supports Link-local Signaling (LLS)
Index 3/5, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 1
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 1.1.3.3 (Backup Designated Router)
Suppress hello for 0 neighbor(s)
R5#sh run int s0/0.235
Building configuration...
Current configuration : 166 bytes
!
interface Serial0/0.235 multipoint
ip address 1.1.235.5 255.255.255.0
frame-relay map ip 1.1.235.2 502 broadcast
frame-relay map ip 1.1.235.3 503 broadcast
router ospf 1
router-id 1.1.5.5
log-adjacency-changes
network 1.1.5.5 0.0.0.0 area 0
network 1.1.235.5 0.0.0.0 area 0
As you can see the neighbor command is gone in OSPF when I reload why why??
thanks
Aamir
On 9/1/06, Scott Morris <swm@emanon.com> wrote:
>
> Did you change anything else? Try looking at "show ip ospf interface
> s0/0.235" and what does it tell you? Or "show run int s0/0.235" to see
> what
> may have been put in there to change things.
>
> HTH,
>
>
> Scott Morris, CCIE4 (R&S/ISP-Dial/Security/Service Provider) #4713, JNCIE
> #153, CISSP, et al.
> CCSI/JNCI-M/JNCI-J
> IPExpert VP - Curriculum Development
> IPExpert Sr. Technical Instructor
> smorris@ipexpert.com
> http://www.ipexpert.com
>
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Aamir Aziz
> Sent: Friday, September 01, 2006 8:57 AM
> To: ccielab@groupstudy.com
> Subject: Weird problem with OSPF
>
> HI there ppl,
>
> I have a hub and spoke environment like this R2-------R5-------R3,
>
> R5 is the hub with s0/0.235 multipoint interface meaning by default NBMA
> mode, which requires neighbor command on R5 but when i reboot R5 i get
> this
> error :
>
> OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> networks
> OSPF: Neighbor command is allowed only on NBMA and point-to-multipoint
> networks
>
> and the neighbor command is no longer there in OSPF of R5, what is
> happening
> here?? i have given ip ospf priority 0 on R2 and R3 to R5 as DR
>
> Thanks
> Aamir
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Oct 01 2006 - 16:55:39 ART