From: Victor Cappuccio (cvictor@protokolgroup.com)
Date: Wed Aug 16 2006 - 17:31:16 ART
It should
*Mar 1 00:06:00.043: IP: s=150.1.5.5 (FastEthernet0/0), d=137.1.54.4
(FastEthernet0/0), len 100, rcvd 3
*Mar 1 00:06:00.047: IP: s=137.1.54.4 (local), d=150.1.5.5, len 100,
unroutable
Are you sure that the 150.1.5.5 is globally routable
*Mar 1 00:06:22.762: IP: s=0.0.0.0 (Ethernet0/0), d=255.255.255.255, len
604, rcvd 2
*Mar 1 00:06:23.512: IP: s=204.12.1.5 (local), d=137.1.54.4, len 100,
policy match
*Mar 1 00:06:23.516: IP: route map POLICY, item 10, permit
*Mar 1 00:06:23.516: IP: s=204.12.1.5 (local), d=137.1.54.4 (Loopback0),
len 100, policy routed
*Mar 1 00:06:23.516: IP: local to Loopback0 137.1.54.4
*Mar 1 00:06:23.516: NAT: s=204.12.1.5->150.1.5.5, d=137.1.54.4 [27]
*Mar 1 00:06:23.520: IP: tableid=0, s=150.1.5.5 (Loopback0), d=137.1.54.4
(Ethernet0/0), routed via FIB
*Mar 1 00:06:23.520: IP: s=150.1.5.5 (Loopback0), d=137.1.54.4
(Ethernet0/0), g=137.1.54.4, len 100, forward.
Success rate is 0 percent (0/1)
R5#
Thanks
Victor.-
-----Mensaje original-----
De: nobody@groupstudy.com [mailto:nobody@groupstudy.com] En nombre de Scott
Smith
Enviado el: Miircoles, 16 de Agosto de 2006 04:03 p.m.
Para: groupstudy
Asunto: NAT - Should this config work?
interface Loopback0
ip address 150.1.5.5 255.255.255.0
ip nat outside
!
interface Ethernet0/0
ip address 204.12.1.5 255.255.255.0
ip nat inside
!
ip local policy route-map POLICY
ip nat inside source list 1 interface Loopback0 overload
!
access-list 1 permit 204.12.1.0 0.0.0.255
!
route-map POLICY permit 10
match ip address 1
set interface Loopback0
============================================================
Rack1R5#ping 137.1.54.4 source e0/0 repeat 1
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 137.1.54.4, timeout is 2 seconds:
Packet sent with a source address of 204.12.1.5
01:26:17: IP: s=204.12.1.5 (local), d=137.1.54.4, len 100, policy match
01:26:17: ICMP type=8, code=0
01:26:17: IP: route map POLICY, item 10, permit
01:26:17: IP: s=204.12.1.5 (local), d=137.1.54.4 (Loopback0), len 100,
policy routed
01:26:17: ICMP type=8, code=0
01:26:17: IP: local to Loopback0 137.1.54.4
01:26:17: IP: tableid=0, s=204.12.1.5 (Loopback0), d=137.1.54.4
(BVI1), routed via FIB
01:26:17: IP: s=204.12.1.5 (Loopback0), d=137.1.54.4 (BVI1),
g=137.1.54.4, len 100, forward
01:26:17: ICMP type=8, code=0.
Success rate is 0 percent (0/1)
Rack1R5#sh deb
Generic IP:
IP packet debugging is on (detailed)
IP NAT debugging is on
IP NAT detailed debugging is on
Policy Routing:
Policy routing debugging is on
TIA!
-Scott
This archive was generated by hypermail 2.1.4 : Fri Sep 01 2006 - 15:41:57 ART