From: Sami (sy1977@gmail.com)
Date: Thu Aug 03 2006 - 13:00:23 ART
Thanks Elias.
If there is only one DLCI and there is no requirement of FRTS, can we map
service policy directly on FR physical inteface. will it work or not?
I tried to apply service policy with random-detect and router..crashed..
R2(config-pmap-c)#^Z
R2#s
*Aug 3 15:54:34.457: %SYS-5-CONFIG_I: Configured from console by console
R2#sho
R2#show poli
R2#show policy-map
R2#show policy-map
Policy Map ALL-TRAFFIC
Class class-default
Bandwidth 60 (%)
exponential weight 9
explicit congestion notification
class min-threshold max-threshold mark-probablity
----------------------------------------------------------
0 - - 1/10
1 - - 1/10
2 - - 1/10
3 - - 1/10
4 - - 1/10
5 - - 1/10
6 - - 1/10
7 - - 1/10
rsvp - - 1/10
R2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#int
R2(config)#interface s0/0/0
R2(config-if)#se
R2(config-if)#serv
R2(config-if)#service-policy ou
R2(config-if)#service-policy output ALL-TRAFFIC
R2(config-if)#^Z
R2#sho
*Aug 3 15:55:29.325: %SYS-5-CONFIG_I: Configured from console by console
R2#sho
R2#show pol
R2#show policy-map
R2#show policy-map int
R2#show policy-map interface s0/0/0
15:55:37 UTC Thu Aug 3 2006: TLB (load or instruction fetch) exception, CPU
signal 10, PC = 0x41E69F1C
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x41E69F1C 0x414A34CC 0x414A38C0 0x402D4ECC 0x402D7038
0x402D79E0 0x41E5FAE0 0x41E5F624 0x41E62D58 0x41E62DA8 0x41E62DFC 0x41298BD0
0x412B7604 0x42339794 0x42339778
$0 : 00000000, AT : 45490000, v0 : 00000004, v1 : FFFFFFFF
a0 : 00000070, a1 : FFFFFFFF, a2 : 00000004, a3 : 4668E6B8
t0 : 45FB305C, t1 : 45A57BF8, t2 : 00000000, t3 : 00000000
t4 : 00000000, t5 : 00000000, t6 : 00000000, t7 : 45FB1BE4
s0 : 73202020, s1 : 4668E710, s2 : 442976C8, s3 : 44297A68
s4 : 45FB163C, s5 : 00000040, s6 : 00000001, s7 : 46923CA8
t8 : 00000000, t9 : 45FB240C, k0 : 45B42FCC, k1 : 423495EC
gp : 4549C54C, sp : 4668E6E0, s8 : 00000200, ra : 41E69F1C
EPC : 41E69F1C, ErrorEPC : BFC0900C, SREG : 3400FF03
MDLO : 00000000, MDHI : 00000007, BadVaddr : 7320202C
Cause 00000008 (Code 0x2): TLB (load or instruction fetch) exception
Writing crashinfo to flash:crashinfo_20060803-155537
15:55:37 UTC Thu Aug 3 2006: TLB (load or instruction fetch) exception, CPU
signal 10, PC = 0x41E69F1C
--------------------------------------------------------------------
Possible software fault. Upon reccurence, please collect
crashinfo, "show tech" and contact Cisco Technical Support.
--------------------------------------------------------------------
-Traceback= 0x41E69F1C 0x414A34CC 0x414A38C0 0x402D4ECC 0x402D7038
0x402D79E0 0x41E5FAE0 0x41E5F624 0x41E62D58 0x41E62DA8 0x41E62DFC 0x41298BD0
0x412B7604 0x42339794 0x42339778
$0 : 00000000, AT : 45490000, v0 : 00000004, v1 : FFFFFFFF
a0 : 00000070, a1 : FFFFFFFF, a2 : 00000004, a3 : 4668E6B8
t0 : 45FB305C, t1 : 45A57BF8, t2 : 00000000, t3 : 00000000
t4 : 00000000, t5 : 00000000, t6 : 00000000, t7 : 45FB1BE4
s0 : 73202020, s1 : 4668E710, s2 : 442976C8, s3 : 44297A68
s4 : 45FB163C, s5 : 00000040, s6 : 00000001, s7 : 46923CA8
t8 : 00000000, t9 : 45FB240C, k0 : 45B42FCC, k1 : 423495EC
gp : 4549C54C, sp : 4668E6E0, s8 : 00000200, ra : 41E69F1C
EPC : 41E69F1C, ErrorEPC : BFC0900C, SREG : 3400FF03
MDLO : 00000000, MDHI : 00000007, BadVaddr : 7320202C
Cause 00000008 (Code 0x2): TLB (load or instruction fetch) exception
-Traceback= 0x41E69F1C 0x414A34CC 0x414A38C0 0x402D4ECC 0x402D7038
0x402D79E0 0x41E5FAE0 0x41E5F624 0x41E62D58 0x41E62DA8 0x41E62DFC 0x41298BD0
0x412B7604 0x42339794 0x42339778
=== Flushing messages (15:55:37 UTC Thu Aug 3 2006) ===
Queued messages::
m e
*** System received a Bus Error exception ***
signal= 0xa, code= 0x8, context= 0x456d3444
PC = 0x4008ff84, Cause = 0x2020, Status Reg = 0x34008002
System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
Copyright (c) 2005 by cisco Systems, Inc.
Initializing memory for ECC
Initializing memory for ECC
.
c2811 processor with 262144 Kbytes of main memory
Main memory is configured to 64 bit mode with ECC enabled
On 8/3/06, Elias Chari <elias.chari@gmail.com> wrote:
>
> It won't until traffic shaping is enabled.
>
> On 8/3/06, Sami <sy1977@gmail.com> wrote:
>
> > Group,
>
> Show policy-map interface command doesn't show anything if a service
> policy
> using MQC is applied using FR class-map to a FR interface. Which command
> show the service policy applied to FR interface ?
>
> Thanks
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Sep 01 2006 - 15:41:55 ART