From: Jens Petter (jenseike@start.no)
Date: Sun Jul 23 2006 - 06:59:56 ART
It is on... look at the output below :
nhus-gw#sh deb
Generic IP:
ICMP packet debugging is on
-----Original Message-----
From: Magmax [mailto:magmax@bigpond.net.au]
Sent: 23. juli 2006 11:55
To: 'Jens Petter'; ccielab@groupstudy.com
Subject: RE: no logging on my icmp debugs
Please turn on debugging
Debug ip icmp
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of Jens
Petter
Sent: Sunday, 23 July 2006 7:30 PM
To: ccielab@groupstudy.com
Subject: no logging on my icmp debugs
Hi all..
I am trying to debug on a 3640 some icmp request generated locally on the
router..
The debugs don't show either in the buffer or in the logg. This is my
logging setting :
nhus-gw#sh run | in logg
logging buffered 4096 debugging
no logging rate-limit
no logging trap
nhus-gw#
my buffer is emty and is not logging
nhus-gw#sh deb
Generic IP:
ICMP packet debugging is on
nhus-gw#ping 213.225.71.74
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 213.225.71.74, timeout is 2 seconds:
....
Success rate is 0 percent (0/4)
nhus-gw#sh logg
Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0
flushes, 0 overruns)
Console logging: level debugging, 75 messages logged
Monitor logging: level debugging, 0 messages logged
Buffer logging: level debugging, 6 messages logged
Logging Exception size (0 bytes)
Trap logging: disabled
Log Buffer (4096 bytes):
Jul 23 09:22:08.131: %SYS-5-CONFIG_I: Configured from console by jpe on vty0
(213.162.236.146)
Jul 23 09:23:14.175: %SYS-5-CONFIG_I: Configured from console by jpe on vty0
(213.162.236.146)
Jul 23 09:23:26.991: %SYS-5-CONFIG_I: Configured from console by jpe on vty0
(213.162.236.146)
Jul 23 09:23:41.243: %SYS-5-CONFIG_I: Configured from console by jpe on vty0
(213.162.236.146)
Jul 23 09:24:14.702: %SYS-5-CONFIG_I: Configured from console by jpe on vty0
(213.162.236.146)
Jul 23 09:25:17.902: %SYS-5-CONFIG_I: Configured from console by jpe on vty0
(213.162.236.146)
interface FastEthernet2/0
no ip address
no ip route-cache cef
no ip route-cache
no ip mroute-cache
duplex auto
speed auto
interface FastEthernet2/0.100
description 12 etg
encapsulation dot1Q 100
ip address 213.225.71.73 255.255.255.252
no ip redirects
no ip route-cache
no ip mroute-cache
service-policy output SHAPE-KUNDER
Why I am not logging anything either to the buffer or consol from my icmp
debugs??
However when I try to debug f eks ospf it is logging fine
OSPF adjacency events debugging is on
nhus-gw#deb ip ospf ev
OSPF events debugging is on
nhus-gw#clear ip osp pr
Reset ALL OSPF processes? [no]: y
nhus-gw#sh logg
Syslog logging: enabled (0 messages dropped, 1 messages rate-limited, 0
flushes, 0 overruns)
Console logging: level debugging, 174 messages logged
Monitor logging: level debugging, 0 messages logged
Buffer logging: level debugging, 105 messages logged
Logging Exception size (0 bytes)
Trap logging: disabled
Log Buffer (4096 bytes):
.235.18 (id)
OSPF: Interface FastEthernet2/0.101 going Down
OSPF: 213.162.235.18 address 213.225.71.129 on FastEthernet2/0.101 is dead,
state DOWN
OSPF: Neighbor change Event on interface FastEthernet2/0.101
OSPF: DR/BDR election on FastEthernet2/0.101
OSPF: Elect BDR 0.0.0.0
OSPF: Elect DR 0.0.0.0
OSPF: Elect BDR 0.0.0.0
OSPF: Elect DR 0.0.0.0
DR: none BDR: none
Jens
This archive was generated by hypermail 2.1.4 : Tue Aug 01 2006 - 07:13:48 ART