From: Petr Lapukhov (petrsoft@gmail.com)
Date: Wed May 31 2006 - 12:21:12 ART
Dave, this is strange :)
just labbed your config:
--------------
access-list 100 permit icmp any any
class-map match-all NO_VOICE
match not access-group 100
policy-map FRAGMENT
class NO_VOICE
map-class frame-relay FRAG
service-policy output FRAGMENT
frame-relay fragment 40
interface Serial0/1
description == Frame-Relay
ip address 172.16.13.1 255.255.255.0
encapsulation frame-relay
frame-relay class FRAG
frame-relay traffic-shaping
frame-relay map ip 172.16.13.3 103 broadcast
no frame-relay inverse-arp
-----------
now, some show outputs:
R1#show policy-map interface serial 0/1 dlci 103
Serial0/1: DLCI 103 -
Service-policy output: FRAGMENT
Class-map: NO_VOICE (match-all)
168 packets, 13525 bytes
5 minute offered rate 0 bps
Match: not access-group 100
Class-map: class-default (match-any)
13 packets, 1332 bytes
5 minute offered rate 0 bps, drop rate 0 bps
Match: any
R1#show interfaces serial 0/1 | inc Output queue
Output queue: high size/max/dropped 0/256/0
Output queue: 0/128 (size/max)
R1#show frame-relay fragment | inc interf|103
interface dlci frag-type size in-frag out-frag
dropped-frag
Se0/1 103 end-to-end 40 0 345 0
R1#debug frame-relay fragment interface serial 0/1 103
This may severely impact network performance.
You are advised to enable 'no logging console debug'. Continue?[confirm]
Frame Relay fragment/packet debugging is on
Displaying fragments/packets on interface Serial0/1 dlci 103 only
R1#ping 172.16.13.3 size ?
<36-18024> Datagram size
R1#ping 172.16.13.3 size 36
Type escape sequence to abort.
Sending 5, 36-byte ICMP Echos to 10.10.13.3, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 12/14/16 ms
R1#ping 172.16.13.3 size 100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.13.3, timeout is 2 seconds:
*May 17 10:42:52.670: Serial0/1(o): dlci 103, tx-seq-num 458, B bit set,
frag_hdr 03 B1 82 CA
*May 17 10:42:52.670: Serial0/1(o): dlci 103, tx-seq-num 459, no bit set,
frag_hdr 03 B1 02 CB
*May 17 10:42:52.670: Serial0/1(o): dlci 103, tx-seq-num 460, E bit set,
frag_hdr 03 B1 42 CC .
*May 17 10:42:54.670: Serial0/1(o): dlci 103, tx-seq-num 461, B bit set,
frag_hdr 03 B1 82 CD
*May 17 10:42:54.670: Serial0/1(o): dlci 103, tx-seq-num 462, no bit set,
frag_hdr 03 B1 02 CE
*May 17 10:42:54.670: Serial0/1(o): dlci 103, tx-seq-num 463, E bit set,
frag_hdr 03 B1 42 CF .
*May 17 10:42:56.670: Serial0/1(o): dlci 103, tx-seq-num 464, B bit set,
frag_hdr 03 B1 82 D0
*May 17 10:42:56.670: Serial0/1(o): dlci 103, tx-seq-num 465, no bit set,
frag_hdr 03 B1 02 D1
*May 17 10:42:56.670: Serial0/1(o): dlci 103, tx-seq-num 466, E bit set,
frag_hdr 03 B1 42 D2 .
*May 17 10:42:58.670: Serial0/1(o): dlci 103, tx-seq-num 467, B bit set,
frag_hdr 03 B1 82 D3
*May 17 10:42:58.670: Serial0/1(o): dlci 103, tx-seq-num 468, no bit set,
frag_hdr 03 B1 02 D4
*May 17 10:42:58.670: Serial0/1(o): dlci 103, tx-seq-num 469, E bit set,
frag_hdr 03 B1 42 D5 .
*May 17 10:43:00.670: Serial0/1(o): dlci 103, tx-seq-num 470, B bit set,
frag_hdr 03 B1 82 D6
*May 17 10:43:00.670: Serial0/1(o): dlci 103, tx-seq-num 471, no bit set,
frag_hdr 03 B1 02 D7
*May 17 10:43:00.670: Serial0/1(o): dlci 103, tx-seq-num 472, E bit set,
frag_hdr 03 B1 42 D8 .
Success rate is 0 percent (0/5)
Petr
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:23 ART