From: Adam S. Roth (adam@therothfamily.net)
Date: Sat May 27 2006 - 08:22:38 ART
Loke:
That's what did it. Thanks!!
Adam
This email message and any attachments are intended for the use of the
addressee(s) indicated above. Information that is privileged or otherwise
confidential may be contained herein. If you are not the intended
recipient(s), you are hereby notified that any dissemination, review, or use
of this message, documents, or information contained herein is strictly
prohibited.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of loke
Sent: Saturday, May 27, 2006 12:24 AM
To: Duncan Maccubbin
Cc: ccielab@groupstudy.com
Subject: Re: OSPF - NMC Lab 2
on the router interface
ip ospf mtu-ignore
On 5/26/06, Duncan Maccubbin <duncan.maccubbin@earthlink.net> wrote:
>
> The MTU on the CAT is set to 1504. You'll need to set it to 1500 and
> reboot the CAT. I think you could see it pretty clearly with:
>
> debug ip ospf adj
>
> -----Original Message-----
> >From: "Adam S. Roth" <adam@therothfamily.net>
> >Sent: May 26, 2006 8:17 PM
> >To: ccielab@groupstudy.com
> >Subject: OSPF - NMC Lab 2
> >
> >I am kind of stuck. I did some searching online, on Cisco and some
> >group study archive searching and still cant get the following error
> >message to stop :
> >
> >00:21:45: %OSPF-5-ADJCHG: Process 1, Nbr 172.16.102.1 on Vlan40 from
> >DOWN
> to
> >DOW
> >N, Neighbor Down: Dead timer expired
> >00:23:02: %OSPF-5-ADJCHG: Process 1, Nbr 172.16.102.1 on Vlan40 from
> EXSTART
> >to
> >DOWN, Neighbor Down: Too many DBD retransmitions
> >00:23:45: %OSPF-5-ADJCHG: Process 1, Nbr 172.16.102.1 on Vlan40 from
> >DOWN
> to
> >DOW
> >N, Neighbor Down: Dead timer expired00:27:02: %OSPF-5-ADJCHG: Process
> >1,
> Nbr
> >172.16.102.1 on Vlan40 from EXSTART to
> >DOWN, Neighbor Down: Too many DBD retransmitions
> >
> >
> >
> >Orginally , by mistake I assign the same loop back to R2 and Cat1. I
> >removed the wrong one, did a write mem and then a reboot and those
> messages
> >above appeared.
> >
> >I checked duplex, here is vlan 40 from CAT1
> >
> >Vlan40 is up, line protocol is up
> > Hardware is EtherSVI, address is 000a.b712.9680 (bia
> >000a.b712.9680)
> > Internet address is 172.16.20.10/25
> > MTU 1504 bytes, BW 1000000 Kbit, DLY 10 usec,
> > reliability 255/255, txload 1/255, rxload 1/255
> > Encapsulation ARPA, loopback not set
> > ARP type: ARPA, ARP Timeout 04:00:00
> > Last input 00:00:05, output 00:00:07, output hang never
> > Last clearing of "show interface" counters never
> > Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 4
> > Queueing strategy: fifo
> > Output queue: 0/40 (size/max)
> > 5 minute input rate 0 bits/sec, 0 packets/sec
> > 5 minute output rate 0 bits/sec, 0 packets/sec
> > 352 packets input, 32794 bytes, 0 no buffer
> > Received 0 broadcasts (0 IP multicast)
> > 0 runts, 0 giants, 0 throttles
> > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
> > 343 packets output, 30928 bytes, 0 underruns
> > 0 output errors, 0 interface resets
> > 0 output buffer failures, 0 output buffers swapped out
> >
> >What else should I check?
> >
> >
> >Thanks
> >
> >
> >Adam
> >
> >_____________________________________________________________________
> >__
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
> ______________________________________________________________________
> _
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:22 ART