From: Jai Prakash (jpjsr06@gmail.com)
Date: Mon May 08 2006 - 06:43:22 ART
Hi GS,
Sorry for posting OT. But, I tried to find the solutions for this.I didn't
get any answer for it.
I am using Cisco 7500 Router with IP Base IOS
(slot0:rsp-isv56i-mz_121-2_T.bin).
I am trying to configure CBR option under ATM PVC command , but I am not
getting option.
R_7500_main(config-subif)#pvc finance 11/106
R_7500_main(config-if-atm-)#?
ATM virtual circuit configuration commands:
abr Enter Available Bit Rate (pcr)(mcr)
broadcast Pseudo-broadcast
class-vc Configure default vc-class name
default Set a command to its defaults
dialer set dialer pool this pvc belongs to
encapsulation Select ATM Encapsulation for VC
exit-vc Exit from ATM VC configuration mode
ilmi Configure ILMI management
inarp Change the inverse arp timer on the PVC
no Negate a command or set its defaults
oam Configure oam parameters
oam-pvc Send oam cells on this pvc
protocol Map an upper layer protocol to this connection.
transmit-priority set the transmit priority for this VC
tx-ring-limit Configure PA level transmit ring limit
ubr Enter Unspecified Peak Cell Rate (pcr) in Kbps.
vbr-nrt Enter Variable Bit Rate (pcr)(scr)(bcs)
R_7500_main(config-if-atm-)#
R_7500_main(config-if-atm-)#
I am using following IOS version.
R_7500_main#sh ver
Cisco Internetwork Operating System Software
IOS (tm) RSP Software (RSP-ISV56I-M), Version 12.1(2)T, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 16-May-00 20:37 by ccai
Image text-base: 0x60010908, data-base: 0x614DA000
ROM: System Bootstrap, Version 11.1(8)CA1, EARLY DEPLOYMENT RELEASE SOFTWARE
(fc
1)
BOOTFLASH: GS Software (RSP-BOOT-M), Version 11.1(22)CA, EARLY DEPLOYMENT
RELEAS
E SOFTWARE (fc1)
R_7500_main uptime is 6 weeks, 3 days, 7 minutes
System returned to ROM by reload at 12:30:31 UAE Thu Nov 21 2002
System image file is "slot0:rsp-isv56i-mz_121-2_T.bin"
cisco RSP4 (R5000) processor with 65536K/2072K bytes of memory.
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
Last reset from power-on
G.703/E1 software, Version 1.0.
G.703/JT2 software, Version 1.0.
Channelized E1, Version 1.0.
X.25 software, Version 3.0.0.
Bridging software.
Primary Rate ISDN software, Version 1.1.
Chassis Interface.
2 VIP2 controllers (2 FastEthernet)(2 E1)(1 ATM).
2 FastEthernet/IEEE 802.3 interface(s)
1 ATM network interface(s)
123K bytes of non-volatile configuration memory.
16384K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
8192K bytes of Flash internal SIMM (Sector size 256K).
Slave in slot 3 is running Cisco Internetwork Operating System Software
IOS (tm) RSP Software (RSP-DW-M), Version 12.1(2)T, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2000 by cisco Systems, Inc.
Compiled Tue 16-May-00 20:40 by ccai
Slave: Loaded from system
Slave: cisco RSP4 (R5000) processor with 65536K bytes of memory.
Configuration register is 0x2102
R_7500_main#
R_7500_main#
R_7500_main#
Can anyone tell me which is the minimum version of IOS support CBR option
under ATM PVC configuraion mode??
Any help would be appricated.
Thanks to all of you in advance.
Best Regards,
Jai
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:21 ART