From: JB (jellyboy@gmail.com)
Date: Thu May 04 2006 - 18:08:04 ART
I am guessing its the following, but the router won't take the command:
R4(config-subif)#interface Serial0/0.34 point-to-point
R4(config-subif)#frame-relay interface-dlci 403 ppp virtual-Template 34
R4(config-fr-dlci)#do sh run | b Serial0/0.34 point-to-point
interface Serial0/0.34 point-to-point
frame-relay interface-dlci 403
R3 takes the config.
Cheers,
JB
On 5/4/06, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
> You're not running PPPoFR on R4:
>
> > interface Serial0/0.34 point-to-point
> > frame-relay interface-dlci 403
>
> You need to say:
>
> interface Serial0/0.34 point-to-point
> frame-relay interface-dlci 403 ppp virtual-template34
>
> Also post the routing tables of R3 and R4 if you're still having
> trouble.
>
> HTH,
>
> Brian McGahan, CCIE #8593
> bmcgahan@internetworkexpert.com
>
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
> Toll Free: 877-224-8987 x 705
> Outside US: 775-826-4344 x 705
> 24/7 Support: http://forum.internetworkexpert.com
> Live Chat: http://www.internetworkexpert.com/chat/
>
>
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> Of JB
> > Sent: Thursday, May 04, 2006 3:45 PM
> > To: ccielab@groupstudy.com
> > Subject: Virtual-Template woes
> >
> > Hi group, I am having problmes with PPPoFR. R3 is connected to R4 via
> > FR. Chap authentication is successful. However when I ping between R3
> > and R4 I am getting 50% packet loss. I am not too familiar with this
> > virtual-template. Is this normal behavior? I expect not......
> >
> > R3----->304---->FR<------403-------R4
> >
> > Thx
> >
> > JB
> >
> >
> > #R3
> >
> > username R4 password 0 xxx
> >
> > interface Serial0/0
> > no ip address
> > encapsulation frame-relay
> > !
> > interface Serial0/0.34 point-to-point
> > frame-relay interface-dlci 304 ppp Virtual-Template34
> >
> > !
> > interface Virtual-Template34
> > ip address 172.16.34.3 255.255.255.0
> > no peer neighbor-route
> > ppp authentication chap
> >
> > R3#sh fram map
> > Serial0/0.34 (up): point-to-point dlci, dlci 304(0x130,0x4C00),
> broadcast
> > status defined, active
> >
> > R3#ping 172.16.34.4
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 172.16.34.4, timeout is 2 seconds:
> > !.!.!
> > Success rate is 60 percent (3/5), round-trip min/avg/max = 52/52/52 ms
> >
> > ++++++++++++++++++
> >
> > #R4
> >
> > username R3 password 0 xxx
> >
> > interface Serial0/0
> > ip address 172.16.124.4 255.255.255.0
> > encapsulation frame-relay
> > no fair-queue
> > !
> > interface Serial0/0.34 point-to-point
> > frame-relay interface-dlci 403
> >
> > !
> > interface Virtual-Template34
> > ip address 172.16.34.4 255.255.255.0
> > no peer neighbor-route
> > ppp authentication chap
> >
> > R4#sh fram map
> > Serial0/0.124 (up): ip 172.16.124.1 dlci 401(0x191,0x6410), static,
> > broadcast,
> > CISCO, status defined, active
> > Serial0/0.124 (up): ip 172.16.124.2 dlci 402(0x192,0x6420), static,
> > broadcast,
> > CISCO, status defined, active
> > Serial0/0.124 (up): ip 172.16.124.4 dlci 402(0x192,0x6420), static,
> > CISCO, status defined, active
> > Serial0/0.34 (up): point-to-point dlci, dlci 403(0x193,0x6430),
> broadcast
> > status defined, active
> >
> > R4#ping 172.16.34.3
> >
> > Type escape sequence to abort.
> > Sending 5, 100-byte ICMP Echos to 172.16.34.3, timeout is 2 seconds:
> > !.!.!
> > Success rate is 60 percent (3/5), round-trip min/avg/max = 52/52/52 ms
> >
> >
> _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Jun 01 2006 - 06:33:20 ART