From: ZeroFlash (Fire_Ice@verizon.net)
Date: Wed Mar 29 2006 - 00:31:03 GMT-3
Guys --
It's the weirdest thing. No configuration change or anything I reloaded the
routers and it magically worked. I don't get it, why didn't it work to start
with??
ZeroFlash
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
ZeroFlash
Sent: Tuesday, March 28, 2006 9:44 PM
To: ccielab@groupstudy.com
Subject: Question for Frame-relay
Guys -
Below is my configuration fro frame-relay and I was wondering if you can
figure out what's wrong. For some reason one spoke will ping consistently to
the hub on both addresses but not the other spoke. The other spoke will in
turn only get every other ping through. I don't understand what I'm doing
wrong and wondering if you guys can help.
Router 2 hub:
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 point-to-point
ip address 1.1.2.1 255.255.255.0
frame-relay interface-dlci 203
!
interface Serial0/0.2 point-to-point
ip address 1.1.2.2 255.255.255.0
frame-relay interface-dlci 204
Router 4 Spoke:
interface Serial1/0
ip address 1.1.2.4 255.255.255.0
encapsulation frame-relay
frame-relay map ip 1.1.2.1 402 broadcast
frame-relay map ip 1.1.2.2 402 broadcast
frame-relay map ip 1.1.2.3 402 broadcast
frame-relay map ip 1.1.2.4 402
no frame-relay inverse-arp
Router 3 Spoke:
interface Serial1/0
ip address 1.1.2.3 255.255.255.0
encapsulation frame-relay
frame-relay map ip 1.1.2.1 302 broadcast
frame-relay map ip 1.1.2.2 302 broadcast
frame-relay map ip 1.1.2.3 302
frame-relay map ip 1.1.2.4 302 broadcast
no frame-relay inverse-arp
R4#ping 1.1.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.2.1, timeout is 2 seconds:
!.!.!
Success rate is 60 percent (3/5), round-trip min/avg/max = 56/57/60 ms
R3#ping 1.1.2.2
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.2.2, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 60/81/116 ms
R3#ping 1.1.2.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.2.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 56/92/116 ms
Debug from R2:
03:17:43: ICMP: time exceeded (time to live) sent to 1.1.2.3 (dest was
1.1.2.4)
R2#
03:17:45: ICMP: time exceeded (time to live) sent to 1.1.2.3 (dest was
1.1.2.4)
R2#
03:22:06: ICMP: echo reply sent, src 1.1.2.1, dst 1.1.2.4
03:22:06: ICMP: echo reply sent, src 1.1.2.1, dst 1.1.2.4
R2#
03:22:08: ICMP: echo reply sent, src 1.1.2.1, dst 1.1.2.4
03:22:08: ICMP: echo reply sent, src 1.1.2.1, dst 1.1.2.4
R2#
03:22:10: ICMP: echo reply sent, src 1.1.2.1, dst 1.1.2.4
R2#
03:22:13: ICMP: time exceeded rcvd from 1.1.2.3
R2#
03:22:15: ICMP: time exceeded rcvd from 1.1.2.3
R2#
03:24:14: ICMP: echo reply sent, src 1.1.2.2, dst 1.1.2.3
03:24:14: ICMP: echo reply sent, src 1.1.2.2, dst 1.1.2.3
03:24:14: ICMP: echo reply sent, src 1.1.2.2, dst 1.1.2.3
03:24:14: ICMP: echo reply sent, src 1.1.2.2, dst 1.1.2.3
03:24:14: ICMP: echo reply sent, src 1.1.2.2, dst 1.1.2.3
See I don't get it
Thanks
ZeroFlash
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:40 GMT-3