From: John Matus (John.Matus@tokiom.com)
Date: Mon Mar 20 2006 - 19:30:39 GMT-3
well, i checked out he bandwidth on all the intrefaces and they are all
1544, mtu is 1500. i thought perhaps there was an interval mismatch
(hellos that i changed to 10 manually......but that did not make a
difference. R3 is sending out hello's on s0/0, but when i debug R2 i
don't see any magic happening
IP-EIGRP Route Events debugging is on
r3#
*Mar 1 01:37:27.739: IP-EIGRP(Default-IP-Routing-Table:100): 183.1.123.0
/24 - do advertise out Serial0/0
r3#
*Mar 1 01:37:32.739: IP-EIGRP(Default-IP-Routing-Table:100): 183.1.123.0
/24 - do advertise out Serial0/0
r3#
*Mar 1 01:37:37.739: IP-EIGRP(Default-IP-Routing-Table:100): 183.1.123.0
/24 - do advertise out Serial0/0
r3#
*Mar 1 01:37:42.739: IP-EIGRP(Default-IP-Routing-Table:100): 183.1.123.0
/24 - do advertise out Serial0/0
Regards,
John D. Matus
Technical Support / PAS
Fujitsu Consulting
626-568-7716
John.Matus@tokiom.com
"Joshua Lauer"
<jslauer@hotmail.
com> To
"John Matus"
03/20/2006 02:14 <John.Matus@tokiom.com>
PM cc
Subject
Re: dumb eigrp adj question
Dont see anything wrong,
I'm assuming all 3 serials are high-speed correct?
Your config looks ok to me otherwise.
JL
Joshua Lauer
CCNA, CCDA, CCNP, CCDP, CCSP, CCIP, RHCE, INFOSEC,
CISSP, CEH
----- Original Message -----
From: "John Matus" <John.Matus@tokiom.com>
To: "Joshua Lauer" <jslauer@hotmail.com>;
<ccielab@groupstudy.com>
Sent: Monday, March 20, 2006 5:08 PM
Subject: Re: dumb eigrp adj question
> opps..........wrong R3 config
> interface Serial0/0
> ip address 183.1.123.3 255.255.255.0
> encapsulation frame-relay
> clockrate 2000000
> frame-relay map ip 183.1.123.1 302
> frame-relay map ip 183.1.123.2 302
> no frame-relay inverse-arp
> frame-relay lmi-type cisco
>
>
> Regards,
>
> John D. Matus
> Technical Support / PAS
> Fujitsu Consulting
> 626-568-7716
> John.Matus@tokiom.com
>
>
>
> "Joshua Lauer"
> <jslauer@hotmail.
> com>
> To
> "John Matus"
> 03/20/2006 02:01
> <John.Matus@tokiom.com>
> PM
> cc
>
>
> Subject
> Re: dumb
> eigrp adj question
>
>
>
>
>
>
>
>
>
>
> John,
>
> Check out your IP address on the second
> spoke..........They are dupes.........
>
>
>
>
> JL
>
>
> Joshua Lauer
> CCNA, CCDA, CCNP, CCDP, CCSP, CCIP, RHCE, INFOSEC,
> CISSP, CEH
>
> ----- Original Message -----
> From: "John Matus" <John.Matus@tokiom.com>
> To: <ccielab@groupstudy.com>
> Sent: Monday, March 20, 2006 4:58 PM
> Subject: dumb eigrp adj question
>
>
>> ok, it's been awhile............
>>
>> hub and spoke eigrp in as 100 all on natural
>> interfaces
>> the hub and 1 spoke form an adj, muut the 2nd
>> spoke will not form the adj,
>> or rather, the 2nd spoke keeps dropping the adj
>> must the hub never show
>> that the adj was formed. i disabled
>> split-horizon, but i forget if there
>> is something else that i'm supposed to do
>>
>> R1- spoke
>> interface Serial0/0
>> bandwidth 1544
>> ip address 183.1.123.1 255.255.255.0
>> encapsulation frame-relay
>> frame-relay map ip 183.1.123.2 102 broadcast
>> frame-relay map ip 183.1.123.3 102
>> no frame-relay inverse-arp
>> frame-relay lmi-type cisco
>>
>> R2-hub
>> interface Serial0/0
>> ip address 183.1.123.2 255.255.255.0
>> encapsulation frame-relay
>> no ip split-horizon eigrp 100
>> frame-relay map ip 183.1.123.1 201 broadcast
>> frame-relay map ip 183.1.123.3 203 broadcast
>> no frame-relay inverse-arp
>>
>> R3- spoke (no adj)
>> interface Serial0/0
>> ip address 183.1.123.2 255.255.255.0
>> encapsulation frame-relay
>> no ip split-horizon eigrp 100
>> frame-relay map ip 183.1.123.1 201 broadcast
>> frame-relay map ip 183.1.123.3 203 broadcast
>> no frame-relay inverse-arp
>>
>>
>> layer 3 us up and both spokes can ping the hub
>> and
>> the others spoke
>>
>>
>>
>> Regards,
>>
>> John D. Matus
>> Technical Support / PAS
>> Fujitsu Consulting
>> 626-568-7716
>> John.Matus@tokiom.com
>>
>
========================================================================================================
>
>> This e-mail is intended solely for the
>> individual to whom it is
>> addressed. The information contained in
>> this transmission contains
>> confidential and/or proprietary information or
>> is
>> otherwise privileged. If
>> the reader of this message is not the intended
>> recipient, please be advised
>> that any dissemination, distribution or
>> copying of this transmission is
>> strictly prohibited. If you have received
>> this e-mail in error, please
>> notify us immediately by returning it to the
>> sender and deleting this copy
>> from your system. Thank you
>> for your cooperation.
>>
>
========================================================================================================
>
>>
>> _______________________________________________________________________
>> Subscription information may be found at:
>> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sat Apr 01 2006 - 10:07:39 GMT-3