From: Greg Gombas (ggombas@hotmail.com)
Date: Wed Jan 25 2006 - 18:48:13 GMT-3
So basically configure the area range command on both R5 and R1?
Thanks for taking the time to look at this.
Regards,
Greg
----Original Message Follows----
From: "Brian Dennis" <bdennis@internetworkexpert.com>
To: "Greg Gombas" <ggombas@hotmail.com>,<ccielab@groupstudy.com>
Subject: RE: IE LAB 7 Task 4.6 OSPF
Date: Wed, 25 Jan 2006 01:03:30 -0500
Greg,
This is a valid solution:
R1:
hostname Rack1R1
!
interface Loopback0
ip address 150.1.1.1 255.255.255.0
!
interface Tunnel0
ip address 163.1.15.1 255.255.255.0
tunnel source Loopback0
tunnel destination 163.1.35.5
!
router ospf 1
area 0 range 150.1.4.0 255.255.254.0
redistribute connected subnets route-map CONNECTED->OSPF
network 163.1.13.1 0.0.0.0 area 1
network 163.1.15.1 0.0.0.0 area 0
!
route-map CONNECTED->OSPF permit 10
match interface Loopback0
R5:
hostname Rack1R5
!
interface Tunnel0
ip address 163.1.15.5 255.255.255.0
tunnel source Serial0/0.35
tunnel destination 150.1.1.1
!
interface Loopback0
ip address 150.1.5.5 255.255.255.0
!
router ospf 1
router-id 150.1.5.5
area 0 range 150.1.4.0 255.255.254.0
network 150.1.5.5 0.0.0.0 area 0
network 163.1.15.5 0.0.0.0 area 0
network 163.1.35.5 0.0.0.0 area 1
R3:
Rack1R3#show ip route 150.1.4.0 255.255.254.0
Routing entry for 150.1.4.0/23
Known via "ospf 1", distance 110, metric 782, type inter area
Last update from 163.1.35.5 on Serial1/0, 00:03:54 ago
Routing Descriptor Blocks:
* 163.1.35.5, from 150.1.5.5, 00:03:54 ago, via Serial1/0
Route metric is 782, traffic share count is 1
Rack1R3#
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Brian Dennis
Sent: Monday, January 23, 2006 11:41 AM
To: Greg Gombas; ccielab@groupstudy.com
Subject: RE: IE LAB 7 Task 4.6 OSPF
Greg,
I'll lab this up tonight and take a look at the issue. There
should be a very easy solution that I'm going to test out.
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: Greg Gombas [mailto:ggombas@hotmail.com]
Sent: Monday, January 23, 2006 8:18 AM
To: Brian Dennis; ccielab@groupstudy.com
Subject: RE: IE LAB 7 Task 4.6 OSPF
Sorry Brian I already wiped the config and moved on to the next lab.
Actually Ali Hasan posted the same question on the IE forum but got no
replies.
----Original Message Follows----
From: "Brian Dennis" <bdennis@internetworkexpert.com>
To: "Greg Gombas" <ggombas@hotmail.com>,<ccielab@groupstudy.com>
Subject: RE: IE LAB 7 Task 4.6 OSPF
Date: Mon, 23 Jan 2006 01:53:52 -0500
Can you send the output of the "show ip route 150.1.0.0 255.255.0.0
longer-prefixes" from R3?
Thanks!
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Greg Gombas
Sent: Sunday, January 22, 2006 2:51 PM
To: ccielab@groupstudy.com
Subject: IE LAB 7 Task 4.6 OSPF
Hello Brians,
Task 4.6 of Volume 1, Lab 7 requires you to use the area range command
to
summarize the 150.1.4.0 routes but later in the excercise you then show
a
virtual link being established to R1 causing it to receive the /32
subnets
from Area0 and forward them R3.
I was just wondering how that would be addressed? I used a distribute
list
on R3 but I was wondering why this wasn't addressed in the solution
guide?
If its just an oversight thats cool but it had me scratching my head for
some time.
I guess a related question would be can you filter intra-area routes
between
routers in the same area?
Thanks,
Greg
This archive was generated by hypermail 2.1.4 : Wed Feb 01 2006 - 07:45:50 GMT-3