From: Gustavo Novais (gustavo.novais@novabase.pt)
Date: Tue Nov 22 2005 - 19:19:50 GMT-3
Hello
There is an example on Ipv6 documentation on doc CD on which they
exemplify peering between two ipv6 bgp peers using link local addresses.
I'm trying to do it on top of a frame-relay connection. Nevertheless,
the peering never comes up. I've checked my FR maps, I've checked
everything but it still will no work.
I'm asking the group if there's anything wrong I'm doing.
R1 Config
Current configuration : 421 bytes
!
interface Serial0/0
ip address 162.1.13.1 255.255.255.0
ip pim sparse-dense-mode
encapsulation frame-relay
ipv6 address FEC0::1/120
no fair-queue
clock rate 256000
frame-relay traffic-shaping
frame-relay map ipv6 FEC0::3 131
frame-relay map ipv6 FE80::20B:46FF:FE86:3900 131 broadcast
frame-relay map ip 162.1.13.3 131 broadcast
frame-relay interface-dlci 131
class QoS9.1
no frame-relay inverse-arp
end
Rack1R1# sh run | b r b
router bgp 200
no synchronization
bgp router-id 150.1.1.1
bgp log-neighbor-changes
neighbor 162.1.13.3 remote-as 300
neighbor 192.10.1.6 remote-as 200
neighbor 192.10.1.254 remote-as 254
neighbor 192.10.1.254 password CISCO
neighbor FE80::20B:46FF:FE86:3900 remote-as 300
neighbor FE80::20B:46FF:FE86:3900 update-source Serial0/0
no auto-summary
!
address-family ipv6
neighbor FE80::20B:46FF:FE86:3900 activate
neighbor FE80::20B:46FF:FE86:3900 route-map NH out
network 2001:CC1E:0:162::/64
exit-address-family
!
route-map NH permit 10
set ipv6 next-hop FEC0::3
!
R3 Config
Rack1R3#sh run int ser0/1
Building configuration...
Current configuration : 330 bytes
!
interface Serial0/1
ip address 162.1.13.3 255.255.255.0
ip pim sparse-dense-mode
encapsulation frame-relay
ipv6 address FEC0::3/120
clock rate 256000
frame-relay map ipv6 FE80::20B:FDFF:FE25:13E0 311 broadcast
frame-relay map ip 162.1.13.1 311 broadcast
frame-relay map ipv6 FEC0::1 311
no frame-relay inverse-arp
end
Rack1R3#sh run | b r b
router bgp 300
no synchronization
bgp router-id 150.1.3.3
bgp log-neighbor-changes
neighbor 162.1.0.2 remote-as 300
neighbor 162.1.0.4 remote-as 100
neighbor 162.1.0.4 remove-private-AS
neighbor 162.1.13.1 remote-as 200
neighbor 162.1.13.1 remove-private-AS
neighbor 162.1.38.8 remote-as 65002
neighbor FE80::20B:FDFF:FE25:13E0 remote-as 200
neighbor FE80::20B:FDFF:FE25:13E0 update-source Serial0/1
no auto-summary
!
address-family ipv6
neighbor FE80::20B:FDFF:FE25:13E0 activate
neighbor FE80::20B:FDFF:FE25:13E0 route-map NEXTHOP out
network 2001:CC1E:0:3::/64
exit-address-family
!
route-map NEXTHOP permit 10
set ipv6 next-hop FEC0::1
Any help will be appreciated
Gustavo Novais
This archive was generated by hypermail 2.1.4 : Thu Dec 01 2005 - 09:12:07 GMT-3