From: Chula Bandara (chula_bandara@hotmail.com)
Date: Sun Nov 06 2005 - 23:35:52 GMT-3
How about using one route-map and one tag instead of two.
router eigrp 1
redistribute ospf 1 route-map Ospf-Eigrp metric 100000 1 255 1 1500
!
router ospf 1
redistribute eigrp 1 route-map Ospf-Eigrp metric 10 metric-type 1
!
route-map Ospf-Eigrp deny 10
match tag 999
!
route-map Ospf-Eigrp permit 20
set tag 999
--------------------------------------------------------------------
From: "Schulz, Dave" <DSchulz@dpsciences.com>
Reply-To: "Schulz, Dave" <DSchulz@dpsciences.com>
To: "kevin gannon " <kevin@gannons.net>, <nobody@groupstudy.com>,
"Cisco Nuts " <cisconuts@hotmail.com>
CC: <ccielab@groupstudy.com>
Subject: RE: Rip <--->Ospf Redistribution - using distribute-lists?
Date: Sat, 5 Nov 2005 12:40:22 -0500
This is a great subject, and one that I have been wrestling with for
awhile.
I have used the ACLs for the distribution, but Kevin is right...you
have to
maintain the ACLs. And, in a dynamic environment, this may take a
lot more
admin than one would care to admit. I have found that easiest way to
do the
redistribution is by using tags. I try to keep the same tag number
as the
administrative distance to keep things straight. So, if I am
redistributing
from OSPF to EIGRP....I use 110 as the tag and 90 in the reverse
direction.
This seems to work well and is very easy to implement and keep things
straight.
The one thing that I have learned with the redistribution is applying
the
metrics. For EIGRP, you must apply the metrics either as a default
in the
routing process or on the redistribute command line. You cannot
solely do
this within the metric. Here is an example of a route-map for
redistribution
that I have used:
router eigrp 1
redistribute ospf 1 route-map Ospf2Eigrp metric 100000 1 255 1 1500
!
router ospf 1
redistribute eigrp 1 route-map Eigrp2Ospf metric 10 metric-type 1
!
route-map Eigrp2Ospf deny 10
match tag 110
!
route-map Eigrp2Ospf permit 20
set tag 90
!
route-map Ospf2Eigrp deny 10
match tag 90
!
route-map Ospf2Eigrp permit 20
set tag 110
I am interested in any other great ways to accomplish this. You
can't know
enough of the ways to do things.
Dave
-----Original Message-----
From: nobody@groupstudy.com
To: Cisco Nuts
Cc: ccielab@groupstudy.com
Sent: 11/5/2005 10:13 AM
Subject: Re: Rip <--->Ospf Redistribution - using distribute-lists?
Both using distance and or distribute lists is a valid way
of stopping the loops. The advantage of the distance way
where possible is you do not have to maintain ACLs so
as new routes get advertised you do not have to update
the ACL's.
It is not always possible to use distance on its own.
Regards
Kevin
On 11/5/05, Cisco Nuts <cisconuts@hotmail.com> wrote:
> Hello: Is distribute-lists a good idea to use when doing 2-way
> redistribution b/w Rip and Ospf or for that matter b/w any 2 IGP's
in
> general? I have been reading a very good example of this on CCO but
did
> not run into this kind of solution (if I recall correctly) when
doing
the
> InetExp Labs. Even a sample lab from DoIt uses the distance 109 for
RIP.
> Permitting all RIP routes into Ospf via the distribute-list out rip
under
> Ospf while denying all RIP routes in via the distribute-list out
ospf
> under Rip seems to nail it down. Any thoughts on this? Thanks!!
>
>
_______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
_______________________________________________________________________
Subscription information may be found at:
http://www.groupstudy.com/list/CCIELab.html
_______________________________________________________________________
Subscription information may be found at:
http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Dec 01 2005 - 09:12:05 GMT-3