From: Mike Flanagan (mikenoc@mindspring.com)
Date: Sun Nov 06 2005 - 14:47:46 GMT-3
I am running 12.2(15)T14 and I believe that this image does not
have OSPFv3 on it :(
Thanks,
Mike F.
On Nov 6, 2005, at 10:15 AM, Jaycee Cockburn - BCX SS wrote:
> Hi All,
> I think the problem is that the IOS/router doesn't support IPV6
> ospf...
> I have a few 2610/2651 with the same problem. Checked it out on
> Feature
> navigator and wa-la, not supported...so I started crying...
>
> If you don't believe me
> -------------SNIP------------------------
> R1(config-subif)#ipv6 ?
> IPv6 interface subcommands:
> address Configure IPv6 address on interface
> enable Enable IPv6 on interface
> mtu Set IPv6 Maximum Transmission Unit
> nat Enable IPv6 NAT on interface
> nd IPv6 interface Neighbor Discovery subcommands
> redirects Enable sending of ICMP Redirect messages
> rip Configure RIP routing protocol
> router IPv6 Router interface commands
> traffic-filter Access control list for packets
> unnumbered Preferred interface for source address selection
> verify Enable per packet validation
>
> R1(config-subif)#ipv6 router ?
> isis IS-IS Routing for IPv6
>
> R1(config-subif)
> -----------------------END-SNIP-------------
>
> It still support RIPng, ISIS, BGPv6, tunnels etc...
>
> Cheers
> Happy Labbing
> JC
>
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
> Behalf Of
> Bruce Porcelli
> Sent: 06 November 2005 05:01 PM
> To: Schulz, Dave; mikenoc@mindspring.com; nobody@groupstudy.com;
> ccielab@groupstudy.com
> Subject: RE: Configuring IPV6 for OSPF question
>
> For IPv6 over frame relay there's a couple of things to remember.
> Specifically, where you are implementing map statements don't forget
> your link-local mappings as well.
>
> otherwise almost identical to ip4. Point-to-Point all you need is
> frame
> interface-dlci # an ipv add / no map needed. (of course ipv uni)
>
> other map and Verify Layer 2 to Layer 3 adjancies.
>
> For the routing protocol to form adjancies / share routing
> updates for
> other than point-to-point conditions, you need to map the link-local
> address of your peer to your local DLCI.
>
> on peer (apply ipv add - then do sh ipv inter)
>
> the good thing. is ipv ospf is virtually the same ip ospf
>
> debug ipv ospf proc :) and others as well
>
> Hope this helps
>
>
>
> "Schulz, Dave" <DSchulz@dpsciences.com> wrote:Did you configure ipv6
> unicast-routing from global config?
>
> -----Original Message-----
> From: nobody@groupstudy.com
> To: ccielab@groupstudy.com
> Sent: 11/6/2005 4:44 AM
> Subject: Configuring IPV6 for OSPF question
>
> I am trying to follow the step by step procedure for configuring
> OSPF on
> IPV6 and it is not letting me. Can someone tell me what command I am
> missing.
>
>
> Thanks,
>
> R4(config)#int ser 0/0
> R4(config-if)#ip address 10.10.10.1 255.255.255.0
> R4(config-if)#ipv6 address 2080:10:10:10::4/64
> R4(config-if)#ipv6 enable
> R4(config-if)#ipv
> R4(config-if)#ipv6 osp
> R4(config-if)#ipv6 osp?
> % Unrecognized command
> R4(config-if)#ipv6 ospf 1 area 0
> ^
> % Invalid input detected at '^' marker.
>
> R4(config-if)#end
> R4#sh ru
> *Mar 4 08:23:46.959: %SYS-5-CONFIG_I: Configured from console by
> consolen | i unicast
> ipv6 unicast-routing
> R4#sh run int ser 0/0
> Building configuration...
>
> Current configuration : 221 bytes
> !
> interface Serial0/0
> ip address 10.10.10.1 255.255.255.0
> encapsulation frame-relay
> ip ospf message-digest-key 1 md5 cisco
> ipv6 address 2080:10:10:10::4/64
> ipv6 enable
> no fair-queue
> no frame-relay inverse-arp
> end
>
> R4#
>
> ______________________________________________________________________
> _
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> ______________________________________________________________________
> _
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
>
>
> Bruce Porcelli
> MCSE/CCNA/CCNP/CCSA
> (631)987-5537
>
>
>
>
> ---------------------------------
> Yahoo! FareChase - Search multiple travel sites in one click.
>
> ______________________________________________________________________
> _
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> ______________________________________________________________________
> _
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Thu Dec 01 2005 - 09:12:05 GMT-3