From: kevin gannon (kevin@gannons.net)
Date: Wed Oct 19 2005 - 14:52:01 GMT-3
Option 1 is fine for what you are doing. You usually use it for p2p
interfaces but what you have configured will work fine.
Regards
Kevin
On 10/19/05, James Matrisciano <jmatrisciano@kenttech.com> wrote:
> All depends on what the requirments say on building the frame
> connection.
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> The Great Ryan
> Sent: Wednesday, October 19, 2005 1:38 PM
> To: Cisco certification
> Subject: Frame-Relay Traffic Shaping using "frame-relay class" &
> "frame-relay interface-dlci"
>
> Hi, Group,
>
> I have configure a Frame-Relay Serial Interface using "frame-relay map"
> statement. I just only use DLCI 205 for sending data. Now I want to
> apply Frame-Relay Traffic shaping on this DLCI. Shoul I use
> 1)
> interface Serial0/1/0
> frame-relay traffic-shaping
> frame-relay map ip 192.168.1.5 205 broadcast frame-relay
> interface-dlci 205
> class FRTS
> 2)
> interface Serial0/1/0
> frame-relay traffic-shaping
> frame-relay map ip 192.168.1.5 205 broadcast frame-relay class FRTS
>
>
> In (1), it can change a particular DLCI's target rate but "frame-relay
> interface-dlci" seem to be used in point-to-point subinterface. I'm not
> sure to use both "frame-relay map" & "frame-relay interface-dlci"
> on the same interface.
>
> In (2), "frame-relay class FRTS" can be applied on main interface but it
> change All DLCI on this main interface to the same traffic rate. I don't
> know if it is suitable or not because I want to change DLCI 205 traffic
> rate only.
>
>
> ======== show traffic-shape (without any map-class)=================
> Interface Se0/1/0
> Access Target Byte Sustain Excess Interval Increment
> Adapt
> VC List Rate Limit bits/int bits/int (ms) (bytes)
> Active
> 203 56000 875 7000 0 125 875 -
> 204 56000 875 7000 0 125 875 -
> 205 56000 875 7000 0 125 875 -
> 201 56000 875 7000 0 125 875 -
>
> ========= show traffic-shape (case 1) =======================
> Interface Se0/1/0
> Access Target Byte Sustain Excess Interval Increment
> Adapt
> VC List Rate Limit bits/int bits/int (ms) (bytes)
> Active
> 203 56000 875 7000 0 125 875 -
> 204 56000 875 7000 0 125 875 -
> 205 128000 2000 128000 0 125 2000 -
> 201 56000 875 7000 0 125 875 -
>
> ========= show traffic-shape (case 2) =======================
> Interface Se0/1/0
> Access Target Byte Sustain Excess Interval Increment
> Adapt
> VC List Rate Limit bits/int bits/int (ms) (bytes)
> Active
> 203 128000 2000 128000 0 125 2000 -
> 204 128000 2000 128000 0 125 2000 -
> 205 128000 2000 128000 0 125 2000 -
> 201 128000 2000 128000 0 125 2000 -
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> --
> This message has been scanned for viruses and
> dangerous content by MailScanner, and is
> believed to be clean.
This archive was generated by hypermail 2.1.4 : Sun Nov 06 2005 - 22:00:51 GMT-3