From: Victor Cappuccio (cvictor@protokolgroup.com)
Date: Thu Oct 13 2005 - 09:41:36 GMT-3
Nice output Danny, please can you do a show run interface serial 0
in R1, Thanks again
Danny Muizebelt wrote:
> Here you go.
>
>
>
> R1#ping 10.2.3.5
>
>
>
> Type escape sequence to abort.
>
> Sending 5, 100-byte ICMP Echos to 10.2.3.5, timeout is 2 seconds:
>
>
>
> Oct 13 14:25:43: Serial0: broadcast search
>
> Oct 13 14:25:43: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:43: Serial0: broadcast search
>
> Oct 13 14:25:43: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:44: Serial0: broadcast search
>
> Oct 13 14:25:44: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:44: Serial0: broadcast search
>
> Oct 13 14:25:44: Serial0:encaps failed on broadcast for link 38(BRIDGE).
>
> Oct 13 14:25:45: Serial0: broadcast search
>
> Oct 13 14:25:45: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:45: Serial0: broadcast search
>
> Oct 13 14:25:45: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:46: Serial0: broadcast search
>
> Oct 13 14:25:46: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:46: Serial0: broadcast search
>
> Oct 13 14:25:46: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:46: Serial0: broadcast search
>
> Oct 13 14:25:46: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Oct 13 14:25:46: Serial0: broadcast search
>
> Oct 13 14:25:46: Serial0:encaps failed on broadcast for link 38(BRIDGE)
>
> Etc.
>
>
>
> A search in Google brought me this link to some unknown mailing list
> with wannabe CCIEs ;)
>
>
>
> http://www.groupstudy.com/archives/ccielab/200009/msg00139.html
>
>
>
> Still doesn't really explain why is has this behaviour and if its normal.
>
>
>
> -Dany
>
>
>
>
>
> ------------------------------------------------------------------------
>
> *Von:* Victor Cappuccio [mailto:cvictor@protokolgroup.com]
> *Gesendet:* Donnerstag, 13. Oktober 2005 14:24
> *An:* Danny Muizebelt
> *Cc:* Cisco certification
> *Betreff:* Re: AW: Router with out any routing Protocol
>
>
>
> Hello Danny, Please can you send us the debug frame-relay packet output
>
> Thanks
>
>
> Danny Muizebelt wrote:
>
>>I notice that R1 and R2 are connected via ethernet. Is this back-
>>
>>to-back or
>>
>>via a switch. If it is via a switch ODR will not work, as the R1
>>
>>and R2
>>
>>will only see the Switch as its CDP neighbor and not each other
>>
>>
>>
>
>
>True. :)
>
>
>
>I also could have mentioned that when using FR the default-gateway
>
>command didn't work. Better said, it would probably work if only I could
>
>ping the gateway. Seems to be an encapsulation problem.
>
>
>
>R1:
>
>interface Serial0
>
> description FR-switch DCE
>
> bandwidth 64
>
> ip address 10.2.3.1 255.255.255.0
>
> encapsulation frame-relay
>
> no fair-queue
>
> clockrate 4000000
>
> cdp enable
>
> frame-relay interface-dlci 115
>
>
>
>R1#conf t
>
>Enter configuration commands, one per line. End with CNTL/Z.
>
>R1(config)#no ip routing
>
>R1(config)#ip default-gateway 10.2.3.5
>
>R1(config)#exit
>
>R1#ping 10.2.3.5
>
>
>
>Type escape sequence to abort.
>
>Sending 5, 100-byte ICMP Echos to 10.2.3.5, timeout is 2 seconds:
>
>
>
>Oct 13 13:48:31: ICMP type=8, code=0
>
>Oct 13 13:48:31: IP: s=10.2.3.1 (local), d=10.2.3.5 (Serial0), len 100,
>
>sending
>
>Oct 13 13:48:31: ICMP type=8, code=0.
>
>Oct 13 13:48:34: IP: s=10.2.3.1 (local), d=10.2.3.5 (Serial0), len 100,
>
>encapsulation failed
>
>Success rate is 0 percent (0/5)
>
>R1#
>
>R1#sh frame-relay map
>
>Serial0 (up): ip 10.2.3.5 dlci 115(0x73,0x1C30), dynamic,
>
> broadcast,, status defined, active
>
>
>
>To be honest, I don't know why it does that.
>
>
>
>-Danny
>
>
>
>
>
>
>
>Diese Information ist vertraulich und ausschlie_lich zur Kenntnisnahme durch den (die) genannten Adressaten bestimmt.
>
>Wenn Sie nicht der vorgesehene Adressat sind, informieren sie uns bitte unverz|glich.
>
>The information herein is confidential and intended solely for the attention and use of the named addressee(s).
>
>If you are not the intended recipient please inform us immediately.
>
>
>
>_______________________________________________________________________
>
>Subscription information may be found at:
>
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Nov 06 2005 - 22:00:50 GMT-3