From: Ali.Huang (zero5291@gmail.com)
Date: Fri Sep 02 2005 - 20:23:15 GMT-3
Hi,ccie2be,
More information,
r5#sh dialer
BRI0/0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0/0:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Dial reason: ip (s=1.1.15.34 <http://1.1.15.34>,
d=1.1.15.33<http://1.1.15.33>
)
Interface bound to profile Di0
Time until disconnect 107 secs
Current call connected 00:00:12
Connected to 7040103 (7040103)
BRI0/0:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Interface bound to profile Di0
Time until disconnect 115 secs
Current call connected 00:00:14
Connected to 7040103
Di0 - dialer type = DIALER PROFILE
Load threshold for dialing additional calls is 25
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is data link layer up
Number of active calls = 2
Dial String Successes Failures Last DNIS Last status
7040103 24 0 00:00:14 successful Default
pls help me to check,thanks.
On 9/3/05, Ali.Huang <zero5291@gmail.com> wrote:
>
> Hi,TIM
> Thanks ccie2b,pls see my configuration,
> R3:
>
> r3#sh run int bri0/0
> Building configuration...
>
> Current configuration : 107 bytes
> !
> interface BRI0/0
> no ip address
> encapsulation ppp
> dialer pool-member 1
> isdn switch-type basic-ni
> end
>
> r3#sh run int d0
> Building configuration...
>
> Current configuration : 159 bytes
> !
> interface Dialer0
> ip address 1.1.15.33 <http://1.1.15.33/>
255.255.255.252<http://255.255.255.252/>
> encapsulation ppp
> dialer pool 1
> dialer remote-name r5
> dialer string 7040105
> dialer-group 1
> end
> R5:
>
> r5#sh run int bri0/0
> Building configuration...
>
> Current configuration : 107 bytes
> !
> interface BRI0/0
> no ip address
> encapsulation ppp
> dialer pool-member 1
> isdn switch-type basic-ni
> end
>
> r5#sh run int d0
> Building configuration...
>
> Current configuration : 194 bytes
> !
> interface Dialer0
> ip address 1.1.15.34 <http://1.1.15.34/>
255.255.255.252<http://255.255.255.252/>
> encapsulation ppp
> dialer pool 1
> dialer remote-name r3
> dialer string 7040103
> dialer load-threshold 25 outbound
> dialer-group 1
> end
> Thanks.If you need more info.pls reply.
>
> On 9/3/05, ccie2be <ccie2be@nyc.rr.com> wrote:
> >
> > Ali,
> >
> > I don't have a clue.
> >
> > If you show your config's I might be able to help you. but, you're not
> > giving me enough to go on.
> >
> > Tim
> >
> > -----Original Message-----
> > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com ] On Behalf Of
> > Ali.Huang
> > Sent: Friday, September 02, 2005 6:38 PM
> > To: Cisco certification
> > Subject:
> >
> > Hi,TIM,
> > I was doing ISDN testing by ping,but the following error occurred by
> > debug
> > ppp ne.
> > Mar 1 09:45: 27.030: BR0/0:2 CDPCP: I CONFACK [ACKsent] id 1 len 4
> > *Mar 1 09:45:27.034: BR0/0:2 CDPCP: State is Open
> > *Mar 1 09:45:28.008: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > BRI0/0:1, changed state to up
> > *Mar 1 09:45: 28.012: %LINEPROTO-5-UPDOWN: Line protocol on Interface
> > BRI0/0:2, changed state to up
> > *Mar 1 09:45:32.980: %ISDN-6-CONNECT: Interface BRI0/0:1 is now
> > connected to
> > 7040103 unknown
> > When I use ping,it's unsucessful,why?pls help me.
> > --
> > THX.
> > Ali.huang
> >
> > _______________________________________________________________________
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
> >
> >
>
>
> --
> THX.
> Ali.huang
-- THX. Ali.huang
This archive was generated by hypermail 2.1.4 : Sun Oct 02 2005 - 14:40:13 GMT-3