From: Nawaz, Ajaz (Ajaz.Nawaz@bskyb.com)
Date: Wed Aug 17 2005 - 08:32:22 GMT-3
This looks like IP Plus feature set (or something like that). What about
enterprise plus...?
Aja
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Rohan Grover (rohang)
Sent: 17 August 2005 07:58
To: swm@emanon.com; ccielab@groupstudy.com
Subject: RE: IPv6 NAT-PT IOS Image
Hi,
I have a 7200 NPE200 running c7200-is-mz.122-15.T12 and the command is
not there :-(
R5#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-IS-M), Version 12.2(15)T12, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Thu 25-Mar-04 04:27 by cmong
Image text-base: 0x60008954, data-base: 0x61C00000
ROM: System Bootstrap, Version 11.1(13)CA, EARLY DEPLOYMENT RELEASE
SOFTWARE (fc1)
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(10)S, EARLY
DEPLOYMENT RELEASE SOFTWARE (fc1)
R5 uptime is 4 days, 19 hours, 2 minutes
System returned to ROM by reload at 02:39:16 UTC Fri Apr 7 1995
System image file is "tftp://5.0.0.2/rohang/c7200-is-mz.122-15.T12"
cisco 7206VXR (NPE200) processor (revision B) with 81920K/16384K bytes
of memory.
Processor board ID 32871203
R5000 CPU at 200Mhz, Implementation 35, Rev 2.1, 512KB L2 Cache
6 slot VXR midplane, Version 2.9
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
8 Ethernet/IEEE 802.3 interface(s)
2 FastEthernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
8 Channelized T1/PRI port(s)
125K bytes of non-volatile configuration memory.
4096K bytes of packet SRAM memory.
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x0
R5#
R5#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R5(config)#int f1/0
R5(config-if)#ipv6 ?
IPv6 interface subcommands:
address Configure IPv6 address on interface
cef Cisco Express Forwarding for IPv6
enable Enable IPv6 on interface
mtu Set IPv6 Maximum Transmission Unit
nd IPv6 interface Neighbor Discovery subcommands
ospf OSPF interface commands
redirects Enable sending of ICMP Redirect messages
rip Configure RIP routing protocol
traffic-filter Access control list for packets
unnumbered Preferred interface for source address selection
verify Enable per packet validation
R5(config-if)#ipv6 n?
nd
R5(config-if)#
===================================================================
Thanks
Rohan
-----Original Message-----
From: Scott Morris [mailto:swm@emanon.com]
Sent: Wednesday, August 17, 2005 12:15 AM
To: Rohan Grover (rohang); ccielab@groupstudy.com
Subject: RE: IPv6 NAT-PT IOS Image
Wow, and hear I thought the point of having a veritable boatload of
addresses in IPV6 was supposed to make NAT die. :) This is a moment of
irony.
Anyway, those commands showed up in 12.2(13)T releases. I have
12.2(15)T9 working on a 3620 and those commands are there. What router
are you on?
Scott
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Rohan Grover (rohang)
Sent: Tuesday, August 16, 2005 6:48 AM
To: ccielab@groupstudy.com
Subject: IPv6 NAT-PT IOS Image
Hi,
Can someone tell me an IOS image that supports IPv6 NAT-PT. I am using
12.2(15)T9 and this does not seem to have the 'ipv6 nat' command under
interface.
Also how likely is it that this topic will appear in the lab? I am a
little unsure about this.
Thanks
Rohan
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:01:19 GMT-3