From: Thomwin Chen (thomwin_chen@yahoo.com)
Date: Wed Aug 03 2005 - 01:56:43 GMT-3
Hi Brian,
thanks.
correct, that's what I mean.
<previous>
you can test it by using a simple command :
debug frame-relay packet and see why most workbooks suggest no
frame-relay inverse-arp configured on physical FR interface
(if the physical FR interface has an IP address or L3 address).
</previous>
what I meant is if the physical FR interface has IP address... :)
and so many DLCIs assigned to it.
Rgds,
Thomwin
Brian Dennis <bdennis@internetworkexpert.com> wrote:
Thomwin,
You do not need to disable inverse-ARP on the physical
interfaces if you are using only subinterfaces. This is because the "no
frame-relay inverse-arp" command is not inherited by subinterfaces.
Here are some examples of when inverse-ARP is enabled or disable
based on the configuration itself or based on the use of the "no
frame-relay inverse-arp" command.
**********************************
*** InARP Enabled for DLCI 102 ***
**********************************
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 multipoint
ip address 10.1.1.1 255.255.255.0
frame-relay interface-dlci 102
**********************************
*** InARP Enabled for DLCI 102 ***
**********************************
interface Serial0/0
no ip address
encapsulation frame-relay
no frame-relay inverse-arp
!
interface Serial0/0.1 multipoint
ip address 10.1.1.1 255.255.255.0
frame-relay interface-dlci 102
***********************************
*** InARP Disabled for DLCI 102 ***
***********************************
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 multipoint
ip address 10.1.1.1 255.255.255.0
frame-relay interface-dlci 102
no frame-relay inverse-arp
*****************************************
*** InARP Disabled for IP on DLCI 102 ***
*****************************************
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 multipoint
ip address 10.1.1.1 255.255.255.0
frame-relay interface-dlci 102
no frame-relay inverse-arp IP 102
*****************************************
*** InARP Disabled for IP on DLCI 102 ***
*****************************************
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 multipoint
ip address 10.1.1.1 255.255.255.0
frame-relay map ip 10.1.1.1 102 broadcast
***********************************
*** InARP Disabled for DLCI 102 ***
***********************************
interface Serial0/0
no ip address
encapsulation frame-relay
!
interface Serial0/0.1 point-to-point
ip address 10.1.1.1 255.255.255.0
frame-relay interface-dlci 102
Also it's a myth (aka urban legend ;-) that the "no arp
frame-relay" command stops the replies to inverse-ARP. It doesn't.
HTH,
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987
Direct: 775-745-6404 (Outside the US and Canada)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Thomwin Chen
Sent: Tuesday, August 02, 2005 8:45 PM
To: Desmond Ong; 'lab'
Subject: Re: frame-relay inverse arp
Hi Desmond,
you can test it by using a simple command :
debug frame-relay packet and see why most workbooks suggest no
frame-relay inverse-arp configured on physical FR interface.
probably, you will also need this to know : no arp frame-relay
Rgds,
Thomwin
Desmond Ong wrote:
hi there,
anyone can enlighten me on the following?
when to use "no frame-relay inverse arp" and when to specifically use
"no
frame-relay inverse arp ip " ???
Thanks!
Regards,
Des
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:01:18 GMT-3