From: Chris Lewis \(chrlewis\) (chrlewis@cisco.com)
Date: Tue Jul 26 2005 - 15:52:34 GMT-3
Hi Gladston,
This is how I would read the output.
GTS acts upon an interface or subinterface. GTS here is configured for a
specific sub-interface and the queue that GTS will build to do shaping
on will use WFQ. The main interface can have fifo or wfq configured on
it. Are you looking at something else?
Chris
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
gladston@br.ibm.com
Sent: Tuesday, July 26, 2005 12:20 PM
To: ccielab@groupstudy.com
Subject: Queue with GTS
Hi,
GTS is applyed to interface serial 0/0.14.
'sh traffic queue' shows that the queue created by GTS uses WFQ.
It seems it does not matter what is configured on the interface, in this
case fifo.
Would you comment this?
Rack2R1(config-subif)#do sh traf que
Traffic queued in shaping queue on Serial0/0.14
Queueing strategy: weighted fair
Queueing Stats: 9/1000/64/10026 (size/max total/threshold/drops)
Conversations 2/4/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 96 kilobits/sec
(depth/weight/total drops/no-buffer drops/interleaves) 5/32384/380/0/0
Conversation 0, linktype: ip, length: 64
source: 150.100.1.254, destination: 148.5.4.1, id: 0x03F6, ttl: 254,
TOS: 0 prot: 17, source port 55172, destination port 5002
(depth/weight/total drops/no-buffer drops/interleaves) 5/32384/766/0/0
Conversation 7, linktype: ip, length: 64
source: 150.100.1.254, destination: 148.5.4.1, id: 0x0020, ttl: 254,
TOS: 0 prot: 17, source port 51068, destination port 5001
Rack2R1(config-subif)#do sh int ser 0/0
Serial0/0 is up, line protocol is up
Hardware is PowerQUICC Serial
MTU 1500 bytes, BW 64 Kbit, DLY 20000 usec,
reliability 255/255, txload 255/255, rxload 10/255
Encapsulation FRAME-RELAY, loopback not set
Keepalive set (10 sec)
LMI enq sent 95, LMI stat recvd 95, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 1023 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 178/0, interface
broadcasts 162
Last input 00:00:01, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:15:49
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops:
10878
Queueing strategy: fifo
Output queue: 0/40 (size/max)
1 minute input rate 95000 bits/sec, 183 packets/sec
1 minute output rate 95000 bits/sec, 185 packets/sec
159447 packets input, 10401005 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
163288 packets output, 10609440 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
This is the config:
interface Serial0/0.14 point-to-point
bandwidth 128
ip address 148.5.14.1 255.255.255.0
traffic-shape rate 96000 12000 1000 1000 frame-relay interface-dlci
104
This archive was generated by hypermail 2.1.4 : Sun Sep 04 2005 - 17:00:31 GMT-3