From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Tue Jun 28 2005 - 04:20:31 GMT-3
Andy,
I believe it depends on the bootrom version. Try it out and see
what happens. If it doesn't work post the error messages and your "show
version" output.
HTH,
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
24/7 Support: http://forum.internetworkexpert.com
Live Chat: http://www.internetworkexpert.com/chat/
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
Of
> Andy Tang
> Sent: Monday, June 27, 2005 9:13 PM
> To: Brian McGahan
> Cc: Chad Hintz; Mathew; Cisco certification
> Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
>
> Hi Brian,
> Can I boot the enterprise plus image c2600-js-mz.122-15.T16.bin from
TFTP
> to the 2620 64MD/16F via the "tftpdnld -r" command in rommon?
> Thanks & regards,
> Andy
>
> On 5/25/05, Brian McGahan <bmcgahan@internetworkexpert.com> wrote:
> >
> > You can boot the 2600XM enterprise plus image from TFTP to the 2610
or
> > 2611 via the "tftpdnld -r" command in rommon.
> >
> > HTH,
> >
> > Brian McGahan, CCIE #8593
> > bmcgahan@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com
> > Toll Free: 877-224-8987 x 705
> > Outside US: 775-826-4344 x 705
> > 24/7 Support: http://forum.internetworkexpert.com
> > Live Chat: http://www.internetworkexpert.com/chat/
> >
> >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On
Behalf
> > Of
> > > Chad Hintz
> > > Sent: Tuesday, May 24, 2005 7:11 AM
> > > To: Mathew; 'Cisco certification'
> > > Subject: Re: Command "ipv6 ospf" on 2600 with IOS 12.2(15)T15
> > >
> > > The 2610 does not support this feature, you need a 2620 or 21 to
use
> > > ospfv3.
> > >
> > > HTH,
> > >
> > > Chad
> > >
> > >
> > > Hi Team
> > >
> > > Does anybody know why I can not enable IPV6 OSPF on 2600 with IOS
ver
> > > 12.2(15)T15?
> > >
> > > Even after configuring "ipv6 unicast-routing" and "ipv6 enable"
under
> > the
> > > interface, I do not see
> > >
> > > a OSPF option.
> > >
> > > Does anybody know why it is so?
> > >
> > > R2(config-if)#ipv6 ?
> > > IPv6 interface subcommands:
> > > address Configure IPv6 address on interface
> > > cef Cisco Express Forwarding for IPv6
> > > enable Enable IPv6 on interface
> > > mtu Set IPv6 Maximum Transmission Unit
> > > nat Enable IPv6 NAT on interface
> > > nd IPv6 interface Neighbor Discovery subcommands
> > > redirects Enable sending of ICMP Redirect messages
> > > rip Configure RIP routing protocol
> > > router IPv6 Router interface commands
> > > traffic-filter Access control list for packets
> > > unnumbered Preferred interface for source address selection
> > > verify Enable per packet validation
> > >
> > > R2(config-if)#ipv6 ro
> > > R2(config-if)#ipv6 router ?
> > > isis IS-IS Routing for IPv6
> > >
> > > R2(config-if)#ipv6 router
> > > R2(config-if)#do sho ver
> > > Cisco Internetwork Operating System Software
> > > IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T15,
RELEASE
> > > SOFTWARE (fc1)
> > > Technical Support: http://www.cisco.com/techsupport
> > > Copyright (c) 1986-2005 by cisco Systems, Inc.
> > > Compiled Thu 03-Mar-05 03:28 by hqluong
> > > Image text-base: 0x80008098, data-base: 0x81960D40
> > >
> > > ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
> > > ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T15, RELEASE
> > SOFTWARE
> > > (fc1)
> > >
> > > R2 uptime is 47 minutes
> > > System returned to ROM by power-on
> > > System image file is "flash:c2600-j1s3-mz.122-15.T15.bin"
> > >
> > > cisco 2610 (MPC860) processor (revision 0x203) with 61440K/4096K
bytes
> > of
> > > memory.
> > > Processor board ID JAD05090GQQ (1222274526)
> > > M860 processor: part number 0, mask 49
> > > Bridging software.
> > > X.25 software, Version 3.0.0.
> > > TN3270 Emulation software.
> > > 1 Ethernet/IEEE 802.3 interface(s)
> > > 2 Serial(sync/async) network interface(s)
> > > 16 terminal line(s)
> > > 32K bytes of non-volatile configuration memory.
> > > 16384K bytes of processor board System flash (Read/Write)
> > >
> > > Configuration register is 0x2102
> > >
> > > R2(config-if)#
> > >
> > >
> >
This archive was generated by hypermail 2.1.4 : Wed Jul 06 2005 - 14:43:45 GMT-3