From: gladston@br.ibm.com
Date: Wed Jun 01 2005 - 16:16:16 GMT-3
I never worry about configuring IP CEF to use ip accounting precedence, but this
router is only accounting packes if cef is enabled. Have you seen this?
R2 is connected to CAT2. Just one link. CAT2 is marking packets.
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 415 packets, 47247 bytes
Precedence 6: 2 packets, 164 bytes
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 415 packets, 47247 bytes
Precedence 6: 2 packets, 164 bytes
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 416 packets, 47360 bytes
Precedence 6: 2 packets, 164 bytes
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 416 packets, 47360 bytes
Precedence 6: 2 packets, 164 bytes
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 416 packets, 47360 bytes
Precedence 6: 2 packets, 164 bytes
r2(config)#ip cef
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 417 packets, 47474 bytes
Precedence 6: 3 packets, 246 bytes
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 433 packets, 49298 bytes
Precedence 6: 3 packets, 246 bytes
r2(config)#do sh int e 0/1 pr
Ethernet0/1
Input
Precedence 5: 463 packets, 52718 bytes
Precedence 6: 3 packets, 246 bytes
r2# sh ver
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE (fc4)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 28-Aug-04 06:47 by cmong
Image text-base: 0x80008098, data-base: 0x819608A4
ROM: System Bootstrap, Version 11.3(2)XA4, RELEASE SOFTWARE (fc1)
ROM: C2600 Software (C2600-J1S3-M), Version 12.2(15)T14, RELEASE SOFTWARE (fc4)
r2 uptime is 7 hours, 9 minutes
System returned to ROM by reload
System image file is "flash:c2600-j1s3-mz.122-15.T14.bin"
cisco 2611 (MPC860) processor (revision 0x203) with 56320K/9216K bytes of memory.
Processor board ID JAD04330EGM (969847152)
M860 processor: part number 0, mask 49
Bridging software.
X.25 software, Version 3.0.0.
TN3270 Emulation software.
Basic Rate ISDN software, Version 1.1.
r2#sh run int e0/1
Building configuration...
Current configuration : 132 bytes
!
interface Ethernet0/1
ip address 172.16.29.2 255.255.255.0
ip accounting precedence input
ip pim sparse-mode
half-duplex
end
This archive was generated by hypermail 2.1.4 : Wed Jul 06 2005 - 14:43:40 GMT-3