From: san (san.study@gmail.com)
Date: Mon May 23 2005 - 00:46:33 GMT-3
Glad / Simon,
Why not "max-reserved-bandwidth" is supported in FR interfaces ?
See the below output, the above command is allowed if fair-queue. I
am missing something very basic, clarify me.
/SAN
Rack1R1#sh queueing inter serial 0/0
Interface Serial0/0 queueing strategy: none
Rack1R1#sh inter serial 0/0
Serial0/0 is up, line protocol is up
Hardware is PowerQUICC Serial
Internet address is 174.1.145.1/24
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY, loopback not set
Keepalive set (10 sec)
LMI enq sent 17069, LMI stat recvd 17050, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 1023 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 19481/0, interface
broadcasts 13519
Last input 00:00:01, output 00:00:01, output hang never
Last clearing of "show interface" counters 1d23h
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1000 bits/sec, 1 packets/sec
5 minute output rate 3000 bits/sec, 1 packets/sec
77933 packets input, 9003395 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
3 input errors, 0 CRC, 3 frame, 0 overrun, 0 ignored, 0 abort
80287 packets output, 11421181 bytes, 0 underruns
0 output errors, 0 collisions, 9 interface resets
0 output buffer failures, 0 output buffers swapped out
4 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Rack1R1#sh queueing inter fas0/0
Interface FastEthernet0/0 queueing strategy: none
Rack1R1#confi t
Enter configuration commands, one per line. End with CNTL/Z.
Rack1R1(config)#inter seri
Rack1R1(config)#inter serial 0/0
Rack1R1(config-if)#max
Rack1R1(config-if)#max-reserved-bandwidth ?
<1-100> Max. reservable bandwidth as % of interface bandwidth
<cr>
Rack1R1(config-if)#max-reserved-bandwidth 50
<<<<<================
Reservable bandwidth is being reduced.
Some existing reservations may be terminated.
Rack1R1(config-if)#exit
Rack1R1(config)#
Rack1R1(config)#end
Rack1R1#sh
*Mar 3 20:49:36.009: %SYS-5-CONFIG_I: Configured from console by console
Rack1R1#sh queueing inter serial 0/0
Interface Serial0/0 queueing strategy: none
Rack1R1#confi t
Enter configuration commands, one per line. End with CNTL/Z.
Rack1R1(config)#inter serial 0/0
Rack1R1(config-if)#fair
Rack1R1(config-if)#fair-queue
Rack1R1(config-if)#end
Rack1R1#
Rack1R1#confi t
*Mar 3 20:50:10.317: %SYS-5-CONFIG_I: Configured from console by console
Rack1R1#sh queueing inter serial 0/0
Interface Serial0/0 queueing strategy: fair
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/1/256 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 772 kilobits/sec ....===================<<<<
On 5/21/05, simon hart <simon.hart@btinternet.com> wrote:
> Gladston,
>
> I see where you are coming from. It would be better phrased (IMHO)
>
> If you apply this policy to a link where the maximum reserved bandwidth is
> 1Mbps...........................................
>
> Also this would work where the configured MinCir for the Frame relay link
> was 1Mbps
>
> Simon
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
> gladston@br.ibm.com
> Sent: 21 May 2005 21:49
> To: ccielab@groupstudy.com
> Subject: Re: GOOD URL: MQC comparing between bandwidth vs priority command
>
>
> Thanks,
>
> Would you think that this phrase on the Doc could be rephrased?
>
> =========================
> policy-map foo
> class bar
> bandwidth percent 30
> class baz
> bandwidth percent 60
> If you apply this policy to a 1 Mbps link, it means that 300 kbps is
> guaranteed to class bar, and 600 kbps is guaranteed to class baz.
> Importantly, 100 kbps is leftover for class-default.
> ===========================
>
> With:
>
> That is true if applyed to a Frame-Relay, where max-reserved-bandwidth
> command is not supported.
>
> If applyed to ATM or Ethernet, the service-policy command will not be
> accepted because only 75% of the interface bandwidth can be used by default.
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
> --
> No virus found in this incoming message.
> Checked by AVG Anti-Virus.
> Version: 7.0.322 / Virus Database: 266.11.14 - Release Date: 20/05/2005
>
> --
> No virus found in this outgoing message.
> Checked by AVG Anti-Virus.
> Version: 7.0.322 / Virus Database: 266.11.14 - Release Date: 20/05/2005
>
> _______________________________________________________________________
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Jun 03 2005 - 10:12:00 GMT-3