From: simon hart (simon.hart@btinternet.com)
Date: Sat May 21 2005 - 17:32:53 GMT-3
What DLSW encapsulation are you using. This will have an impact on what you
are trying to match.
Simon
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
gladston@br.ibm.com
Sent: 21 May 2005 20:54
To: ccielab@groupstudy.com
Subject: Custom Queue Debug
Trying to match DLSW and other traffic on CQ, just one Telnet packet was
logged on debug queueing.
Have you seem this behavior? It is a 2600, 12.2T
Rack2R2#sh queueing custom
Current custom queue configuration:
List Queue Args
1 13 default
1 10 protocol ip tcp port www
1 11 protocol ip tcp port ftp
1 11 protocol ip tcp port ftp-data
1 12 protocol ip tcp port telnet
1 14 protocol dlsw
1 10 byte-count 20000
1 11 byte-count 30000
1 12 byte-count 10000
1 13 byte-count 40000
1 14 byte-count 10000
Rack2R2#deb custom-queue
Custom output queueing debugging is on
*Mar 1 01:50:31.791: CQ: Serial0/0 output (Pk size/Q: 58/13) Q # was 13 now
13
*Mar 1 01:50:31.791: CQ: Serial0/0 output (Pk size/Q: 58/13) Q # was 13 now
13
*Mar 1 01:51:16.103: CQ: Serial0/0 output (Pk size/Q: 32/13) Q # was 12 now
13
*Mar 1 01:51:16.103: CQ: Serial0/0 output (Pk size/Q: 32/13) Q # was 13 now
13
Rack2R2#
*Mar 1 01:51:31.228: CQ: Serial0/0 output (Pk size/Q: 58/13) Q # was 13 now
13
*Mar 1 01:51:31.228: CQ: Serial0/0 output (Pk size/Q: 58/13) Q # was 13 now
13
Rack2R2#
*Mar 1 01:51:52.619: CQ: Serial0/0 output (Pk size/Q: 63/13) Q # was 13 now
13
*Mar 1 01:51:52.860: CQ: Serial0/0 output (Pk size/Q: 44/13) Q # was 13 now
13
Rack2R2#
Rack2R2#sh int ser 0/0
Serial0/0 is up, line protocol is up
Hardware is PowerQUICC Serial
Internet address is 142.20.125.2/27
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation FRAME-RELAY, loopback not set
Keepalive set (10 sec)
LMI enq sent 572, LMI stat recvd 573, LMI upd recvd 0, DTE LMI up
LMI enq recvd 0, LMI stat sent 0, LMI upd sent 0
LMI DLCI 1023 LMI type is CISCO frame relay DTE
FR SVC disabled, LAPF state down
Broadcast queue 0/64, broadcasts sent/dropped 803/0, interface broadcasts
511
Last input 00:00:01, output 00:00:00, output hang never
Last clearing of "show interface" counters 01:35:30
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: custom-list 1
Output queues: (queue #: size/max/drops)
0: 0/20/0 1: 0/20/0 2: 0/20/0 3: 0/20/0 4: 0/20/0
5: 0/20/0 6: 0/20/0 7: 0/20/0 8: 0/20/0 9: 0/20/0
10: 0/20/0 11: 0/20/0 12: 0/20/0 13: 0/20/0 14: 0/20/0
15: 0/20/0 16: 0/20/0
5 minute input rate 0 bits/sec, 1 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
2204 packets input, 116784 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
2201 packets output, 106677 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 output buffer failures, 0 output buffers swapped out
4 carrier transitions
DCD=up DSR=up DTR=up RTS=up CTS=up
Rack2R2#
interface Serial0/0
ip address 142.20.125.2 255.255.255.224
ip pim sparse-dense-mode
encapsulation frame-relay
ip ospf authentication-key cisco
ip ospf priority 0
ipv6 address 2001:125::2/64
custom-queue-list 1
frame-relay map ipv6 2001:125::1 205
frame-relay map ipv6 2001:125::5 205 broadcast
frame-relay map ip 142.20.125.1 205
frame-relay map ip 142.20.125.5 205 broadcast
no frame-relay inverse-arp
This archive was generated by hypermail 2.1.4 : Fri Jun 03 2005 - 10:12:00 GMT-3