From: Joe Freeman (joe.freeman@CenturyTel.com)
Date: Fri May 06 2005 - 17:16:05 GMT-3
Howdy all-
I've got an AS5400 I'm trying to turn up that's connected to one of our
DMS-250's (LD/Class 4 switch) via a CT3 card with 28 T1's on it.
I've got the DS3 up. I've got the T1 spans up. PPP is properly
configured a the global level. Authentication works properly for access
to the box via console and vty ports. Image is running from
flash:c5400-is-mz.123-10c.bin.
Config:
aaa authentication ppp default group tacacs+ local
!
controller T3 7/0
framing m23
clock source line
t1 1-28 controller
description Lightcore DS3 to LD
!
controller T1 7/0:1
framing esf
pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 0
!
interface Serial7/0:1:23
no ip address
encapsulation ppp
dialer rotary-group 1
dialer-group 1
isdn switch-type primary-ni
isdn incoming-voice modem
isdn calling-number 888240-4818
no isdn outgoing ie redirecting-number
no isdn incoming alerting add-PI
compress stac
no cdp enable
interface Group-Async1
ip unnumbered Loopback0
encapsulation ppp
no ip route-cache cef
no ip route-cache
ip tcp header-compression
no ip mroute-cache
dialer in-band
dialer idle-timeout 0
dialer-group 1
autodetect encapsulation ppp
async default routing
async dynamic routing
async mode interactive
no snmp trap link-status
peer default ip address pool analog
compress stac
no fair-queue
ppp authentication pap
ppp multilink
group-range 1/00 6/107
hold-queue 75 in
line 1/00 6/107
no flush-at-activation
modem InOut
transport input all
autoselect during-login
autoselect ppp
debug
(outbound call)
May 6 15:11:01: ISDN Se7/0:1:23 Q931: TX -> SETUP pd = 8 callref =
0x0006
Bearer Capability i = 0x8890
Standard = CCITT
Transer Capability = Unrestricted Digital
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9808381
Exclusive, Interface 0, Channel 1
Calling Party Number i = 0xA1, 'REMOVEDNUMBER'
Plan:ISDN, Type:National
Called Party Number i = 0xA1, 'REMOVEDNUMBER'
Plan:ISDN, Type:National
May 6 15:11:01: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
06
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:01: ISDN Se7/0:1:23 Q931: RX <- SERVICE ACKNOWLEDGE pd = 67
callre
f = 0x8000
Change Status i = 0xC2 - out-of-service
Channel ID i = 0xA98395
Exclusive, Channel 21
May 6 15:11:01: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
06
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:05: ISDN Se7/0:1:23 **ERROR**: CCPCC_CallOrigination: SETUP
timed-o
ut (2nd T303) to NETWORK. The SETUP failed.
May 6 15:11:06: ISDN Se7/0:1:23 Q931: RX <- SERVICE ACKNOWLEDGE pd = 67
callre
f = 0x8000
Change Status i = 0xC2 - out-of-service
Channel ID i = 0xA98396
Exclusive, Channel 22
May 6 15:11:06: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
05
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:06: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
05
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:09: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
05
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:10: ISDN Se7/0:1:23 Q931: RX <- SERVICE ACKNOWLEDGE pd = 67
callre
f = 0x8000
Change Status i = 0xC2 - out-of-service
Channel ID i = 0xA98397
Exclusive, Channel 23
May 6 15:11:10: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
05
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:10: ISDN Se7/0:1:23 Q931: L3_Go: L3_GetUser_NLCB returned
NULL cid
0x0 cr 0x5 ev 0x5A ces 1 -- Message ignored
May 6 15:11:13: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
05
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:13: ISDN Se7/0:1:23 Q931: L3_Go: L3_GetUser_NLCB returned
NULL cid
0x0 cr 0x5 ev 0x5A ces 1 -- Message ignored
May 6 15:11:13: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
06
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:13: ISDN Se7/0:1:23 Q931: L3_Go: L3_GetUser_NLCB returned
NULL cid
0x0 cr 0x6 ev 0x5A ces 1 -- Message ignored
May 6 15:11:17: ISDN Se7/0:1:23 Q931: RX <- RELEASE_COMP pd = 8
callref = 0x80
06
Cause i = 0x80BF - Service/option not available, unspecified
May 6 15:11:17: ISDN Se7/0:1:23 Q931: L3_Go: L3_GetUser_NLCB returned
NULL cid
0x0 cr 0x6 ev 0x5A ces 1 -- Message ignored
(yes, I have all but the first b channel busied out so that the LD
Switch techs can trace the test calls more easily)
Any thoughts or ideas are appreciated.
Joe Freeman
This archive was generated by hypermail 2.1.4 : Fri Jun 03 2005 - 10:11:56 GMT-3