From: Dillon Yang (gzdillon@hotmail.com)
Date: Mon Mar 21 2005 - 02:29:36 GMT-3
Hi, folks:
The following config can not initiate a call. Why?
The PVC 0/32 is valid when it was used as static PVC.
====================================================
hostname r6
!
interface ATM0
no ip address
pvc qq 0/5 qsaal
!
pvc ii 0/16 ilmi
!
no atm ilmi-keepalive
!
interface ATM0.33 point-to-point
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 6
!
!
interface Dialer6
ip address 192.40.50.1 255.255.255.0
encapsulation ppp
dialer pool 6
dialer-group 7
!
dialer-list 7 protocol ip permit
!
======================== server ===========================
!
interface Virtual-Template11
ip add address 192.40.50.10 255.255.255.0
!
interface ATM0.33 point-to-point
description PPP over ATM using Dialer 0/32
pvc 0/32
encapsulation aal5mux ppp Virtual-Template11
!
!
============================================================
r6#s interface ATM0.33
ATM0.33 is up, line protocol is up
Hardware is ATMizer BX-50
MTU 4470 bytes, BW 155520 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ATM
583 packets input, 11660 bytes
675 packets output, 10800 bytes
0 OAM cells input, 0 OAM cells output
r6#s int dial 6
Dialer6 is up, line protocol is up (spoofing)
Hardware is Unknown
Internet address is 192.40.50.1/24
MTU 1500 bytes, BW 56 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
DTR is pulsed for 1 seconds on reset
Interface is bound to Vi1
Last input never, output never, output hang never
Last clearing of "show interface" counters 00:57:32
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: weighted fair
Output queue: 0/1000/64/0 (size/max total/threshold/drops)
Conversations 0/0/16 (active/max active/max total)
Reserved Conversations 0/0 (allocated/max allocated)
Available Bandwidth 42 kilobits/sec
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes
0 packets output, 0 bytes
Bound to:
Virtual-Access1 is up, line protocol is down
Hardware is Virtual Access interface
MTU 1500 bytes, BW 56 Kbit, DLY 100000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation PPP, loopback not set
Keepalive set (10 sec)
DTR is pulsed for 5 seconds on reset
Interface is bound to Di6 (Encapsulation PPP)
LCP Listen
Closed: IPCP, CDPCP
Bound to ATM0.33 VCD: 14, VPI: 0, VCI: 32
Cloned from Dialer6
Last input 00:09:30, output never, output hang never
Last clearing of "show interface" counters 00:56:28
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
563 packets input, 9008 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
680 packets output, 8160 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
0 carrier transitions
r6#
TIA
dillon
This archive was generated by hypermail 2.1.4 : Sun Apr 03 2005 - 17:56:49 GMT-3