From: Scott Morris (swm@emanon.com)
Date: Fri Feb 25 2005 - 09:21:06 GMT-3
The virtual-template is not an interface. It is simply a template to be
used. So it's "interface status" will always show as down.
Once it is used, the information flows into a virtual-access interface.
Being an interface, it's "interface status" will reflect a state of up.
Life is good.
Scott Morris, MCSE, CCDP, CCIE4 (R&S/ISP-Dial/Security/Service Provider)
#4713, JNCIP, CCNA-WAN Switching, CCSP, Cable Communications Specialist, IP
Telephony Support Specialist, IP Telephony Design Specialist, CISSP
CCSI #21903
swm@emanon.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of aji
nc
Sent: Friday, February 25, 2005 7:02 AM
To: ccielab@groupstudy.com
Subject: PPP over frame-relay
hi,
when trying ppp over frame-relay on a point to point link shows me
virtual-template1 down and virtual
access1 up is this a problem or is the correct behavior ? configs attached,
Anyone pls clarify Trying between R4 and R2 With ospf authentication
R2#
interface Serial0/0.1 point-to-point
frame-relay interface-dlci 424 ppp Virtual-Template1 end
interface Virtual-Template1
ip address 135.1.42.2 255.255.255.0
ip ospf authentication
ip ospf authentication-key cmc
end
------------------------------------
R4#
interface Serial0/0.2 point-to-point
frame-relay interface-dlci 442 ppp Virtual-Template1
interface Virtual-Template1
ip address 135.1.42.4 255.255.255.0
ip ospf authentication
ip ospf authentication-key cmc
-------------------------------------------------
r2#sh ip ospf interface
Virtual-Access3 is up, line protocol is up
Internet Address 135.1.42.2/24, Area 0
Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 1
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
oob-resync timeout 40
Hello due in 00:00:09
Index 3/3, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 10, maximum is 16
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 4.4.4.4
Suppress hello for 0 neighbor(s)
Simple password authentication enabled
Virtual-Template1 is down, line protocol is down
Internet Address 135.1.42.2/24, Area 0
Process ID 1, Router ID 2.2.2.2, Network Type POINT_TO_POINT, Cost: 1
Transmit Delay is 1 sec, State DOWN,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
oob-resync timeout 40
-------------------------------------------
r4#sh ip ospf interface
Virtual-Access1 is up, line protocol is up
Internet Address 135.1.42.4/24, Area 0
Process ID 1, Router ID 4.4.4.4, Network Type POINT_TO_POINT, Cost: 1
Transmit Delay is 1 sec, State POINT_TO_POINT,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Hello due in 00:00:02
Index 4/6, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 9
Last flood scan time is 0 msec, maximum is 0 msec
Neighbor Count is 1, Adjacent neighbor count is 1
Adjacent with neighbor 2.2.2.2
Suppress hello for 0 neighbor(s)
Simple password authentication enabled
Virtual-Template1 is down, line protocol is down
Internet Address 135.1.42.4/24, Area 0
Process ID 1, Router ID 4.4.4.4, Network Type POINT_TO_POINT, Cost: 1
Transmit Delay is 1 sec, State DOWN,
Timer intervals configured, Hello 10, Dead 40, Wait 40, Retransmit 5
Does any one there?
Regards
Aji.N.C
__________________________________
Do you Yahoo!?
Yahoo! Mail - Easier than ever with enhanced search. Learn more.
http://info.mail.yahoo.com/mail_250
This archive was generated by hypermail 2.1.4 : Thu Mar 03 2005 - 08:51:25 GMT-3