From: Annu Roopa (annu_roopa@yahoo.com)
Date: Fri Sep 24 2004 - 23:04:00 GMT-3
Couple of Qs?
1. Do u have any authentication configured as i dont see any..i guess not.Does not make a diff, but if u have it then is it working.
2. What happens if u have a dialer list on the R5 (called side) and only permit icmp
echo-reply in that and other cmds are as such.
Annu.
venkat garigipati <garigipati@yahoo.com> wrote:
hi roopa,
i tried that option too..basically, ISDN connection is initiated but ping packets doesnt go thru..I get 0% success..
This is what I did:
On R5:
-----------
username r4 password CISCO
interface BRI0/0
ip address 187.1.45.5 255.255.255.0
encapsulation ppp
dialer idle-timeout 0
dialer map ip 187.1.45.4 name r4 broadcast 11110101
isdn switch-type basic-ni
isdn spid1 22220101
R4:
------
username r5 password CISCO
interface BRI0/0
ip address 187.1.45.4 255.255.255.0
encapsulation ppp
dialer map ip 187.1.45.5 name r5 broadcast 22220101
dialer-group 1
isdn switch-type basic-ni
isdn spid1 11110101
r4#p 187.1.45.5
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 187.1.45.5, timeout is 2 seconds:
*Mar 1 20:26:30.706: %LINK-3-UPDOWN: Interface BRI0/0:2, changed state to up.
*Mar 1 20:26:31.726: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI0/0:2, changed state to up..
*Mar 1 20:26:36.710: %ISDN-6-CONNECT: Interface BRI0/0:2 is now connected to 22220101 r5..
Success rate is 0 percent (0/5)
Annu Roopa <annu_roopa@yahoo.com> wrote:
Venkat,
I do observe a couple of things for u to change.I think what u have interpreted and are doing is rt . But u need to change a little i guess...
If u dont give the dial # then R5 wont be able to respond to the call. U dont need to give the dialer-group cmd on R5 as that is what defines interesting traffic. So without that R5 wont have anything to initiate the call but if u dont give the dial # after bcast it wont know how to call R4..
Make the changes and let us see what happens ??
R5:
-----
username r5 password CISCO <<<< shouldnt this be r4 and not r5
!
interface BRI0/0
ip address 187.1.45.5 255.255.255.0
dialer idle-timeout 0
dialer map ip 187.1.45.4 name r4 broadcast xxxxxx <<< u need to give the dial #
isdn switch-type basic-ni
isdn spid1 22220101
end
Annu
venkat garigipati <garigipati@yahoo.com> wrote:
Right, R5 is not allowed to call R4, but only R4 can make calls to R5. the reason i used dialer idle-timeout 0 is that R5 should never disconnect
Richard Dumoulin wrote:
I interpret "...R5 is not allowed to call R4..." as "do not configure an isdn number under the dialer map command". As this is what you have done
I don't see anything wrong in putting the dialer-group.
I have noticed in Cisco papers that they always put it in the bri/dialer interfaces. Then if they don't want to define interesting traffic they just configure dialer-list protocol ip deny. So it seems to me that the dialer-list command is good practice.
Also why have you configured dialer idle-timeout 0 ?
--Richard
-----Message d'origine-----
De : venkat garigipati [mailto:garigipati@yahoo.com]
Envoyi : Saturday, September 25, 2004 1:51 AM
@ : ccielab@groupstudy.com
Objet : ISDN Issue..
hi
The question is that R4 can call R5 but R5 is not allowed to call R4.. When I do this via a PING the call gets setup but I do not get a response...When I add the dialer-list/dialer-group commands to R5 it works. Below is my config. I am using c3640-js-mz.122-15.T14 image on both R4 & R5..How do I make Only one side initiate the call...?
R5:
-----
username r5 password CISCO
!
interface BRI0/0
ip address 187.1.45.5 255.255.255.0
dialer idle-timeout 0
dialer map ip 187.1.45.4 name r4 broadcast
isdn switch-type basic-ni
isdn spid1 22220101
end
R4:
-----
username r5 password CISCO
!
interface BRI0/0
ip address 187.1.45.4 255.255.255.0
dialer map ip 187.1.45.5 name r5 broadcast 22220101
dialer-group 1
isdn switch-type basic-ni
isdn spid1 11110101
end
!
dialer-list 1 protocol ip permit
---------------------------------
Do you Yahoo!?
Yahoo! Mail - 50x more storage than other providers!
This archive was generated by hypermail 2.1.4 : Fri Oct 01 2004 - 15:00:49 GMT-3