From: Dan Shechter (danshtr@yahoo.com)
Date: Tue Jul 20 2004 - 12:08:14 GMT-3
My test is before August so I am using 12.2
R4(config)#int bri0/0
R4(config-if)#mul
R4(config-if)#multilink ?
load-threshold Specify threshold used to add/delete links
max-fragments Specify the maximum number of fragments per transmitted
packet
max-links Specify upper limit of the number of links in a bundle
min-links Specify lower limit of the number of links in a bundle
R4(config-if)#multilink
Kenneth Wygand wrote:
>?
>Dan,
>
>>From the Doc CD:
>
><snip>
>The dialer load-threshold command is generally configured instead of the ppp multilink load-threshold command, and MLP inherits the values set by the dialer load-threshold command when a bundle configuration is taken from a dialer interface.
></snip>
>
>I couldn't find a reference to the "multilink load-threshold" command. Is this the proper syntax? All I could find starting with "multilink" was:
>
><snip>
>multilink bundle-name DR-506
>multilink max-fragments DR-508
>multilink virtual-template DR-509
>multilink-group DR-507
></snip>
>
>FYI, I am using the 12.3T documentation.
>
>Ken
>
>________________________________
>
>From: nobody@groupstudy.com on behalf of Dan Shechter
>Sent: Tue 7/20/2004 10:23 AM
>To: Noble T N
>Cc: 'Group Study'
>Subject: Re: Multilink - who should dial?
>
>
>
>AFAIK there is no diff between:
>
> 1. dialer load-threshold
> 2. ppp multilink load-threshold
> 3. multilink load-threshold
>
>am i right?
>
>
>Noble T N wrote:
>
>
>
>>Hello:
>>
>>I think this command has not got anything to do with the initial connection
>>initiation. As u say it can sometimes cause some confusion if the same is
>>configured both the ends. To configure bandwidth on demand by setting the
>>maximum load before the dialer places another call to a destination, use the
>>dialer load-threshold command in interface configuration mode.
>>
>>
>>Regards,
>>
>>Noble
>>
>>
>>-----Original Message-----
>>From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
>>Dan Shechter
>>Sent: 20 July 2004 16:31
>>To: Group Study
>>Subject: Multilink - who should dial?
>>
>>
>>Hello all,
>>
>>I have read somewhere that the 'dialer load-threshold' should be
>>configured only on one end, because both side might initiate the
>>connection in the same time and the call won't succeed.
>>
>>Is it right?
>>
>>_______________________________________________________________________
>>Please help support GroupStudy by purchasing your study materials from:
>>http://shop.groupstudy.com <http://shop.groupstudy.com/>
>>
>>Subscription information may be found at:
>>http://www.groupstudy.com/list/CCIELab.html
>>
>>
>
>_______________________________________________________________________
>Please help support GroupStudy by purchasing your study materials from:
>http://shop.groupstudy.com <http://shop.groupstudy.com/>
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
>
>_______________________________________________________________________
>Please help support GroupStudy by purchasing your study materials from:
>http://shop.groupstudy.com
>
>Subscription information may be found at:
>http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Sun Aug 01 2004 - 10:11:59 GMT-3