From: Fernando Rodriguez (fernanrl@yahoo.com)
Date: Tue Jun 22 2004 - 08:55:31 GMT-3
Hi,
It is in my router at least:
Router#
Router#sh ver
Cisco IOS Software, 3700 Software (C3725-IPVOICE-M),
Version 12.3(8)T, RELEASE S
OFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by Cisco Systems, Inc.
Compiled Thu 13-May-04 18:22 by eaarmas
ROM: System Bootstrap, Version 12.2(8r)T2, RELEASE
SOFTWARE (fc1)
Router uptime is 3 minutes
System returned to ROM by power-on
System image file is
"flash:c3725-ipvoice-mz.123-8.T.bin"
Cisco 3725 (R7000) processor (revision 0.1) with
121856K/9216K bytes of memory.
Processor board ID JHY0803K40Y
R7000 CPU at 240MHz, Implementation 39, Rev 3.3, 256KB
L2 Cache
2 FastEthernet interfaces
2 Channelized E1/PRI ports
DRAM configuration is 64 bits wide with parity
disabled.
55K bytes of NVRAM.
31744K bytes of ATA System CompactFlash (Read/Write)
Configuration register is 0x2102
Router#
Router#conf t
Enter configuration commands, one per line. End with
CNTL/Z.
Router(config)#ip pim auto ?
listener Allow AutoRP packets across sparse mode
interface
Router(config)#ip pim auto
Router#
Router(config)#int fa0/1
Router(config-if)#ip pim spar
Router(config-if)#ip pim sparse-den
Router(config-if)#ip pim sparse-dense-mode ?
<cr>
Router(config)#ip pim autorp listener ?
<cr>
Router(config)#ip pim autorp listener
Router#
regards,
Fernando
--- Nigel.Johnson@barclayscapital.com escribis: >
That's strange, it should definitely be available.
> It's listed in the 12.2T
> command ref:
>
>
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122newft/122
> tcr/122tip3r/mult/p3ftmlt2.htm
>
> Nigel
>
> -----Original Message-----
> From: John Matus [mailto:jmatus@pacbell.net]
> Sent: 22 June 2004 12:28
> To: Nigel.Johnson@barclayscapital.com;
> ccielab@groupstudy.com
> Subject: Re: ip pim autorp listerner
>
>
> hmmm......i was working on a lab that was 12.2T but
> did not have that
> feature...i assumed that it had been phased out...
> Regards,
>
> John D. Matus
> MCSE, CCNP
> 818.782.2061 office
> 818.430.8372 mobile
> jmatus@pacbell.net
>
>
> ----- Original Message -----
> From: <Nigel.Johnson@barclayscapital.com>
> To: <jmatus@pacbell.net>; <ccielab@groupstudy.com>
> Sent: Tuesday, June 22, 2004 4:03 AM
> Subject: RE: ip pim autorp listerner
>
>
> > This command didn't exist before 12.2(7). The only
> option before this
> > was
> to
> > run sparse-dense mode.
> >
> > Cheers,
> > Nigel
> >
> > -----Original Message-----
> > From: John Matus [mailto:jmatus@pacbell.net]
> > Sent: 22 June 2004 11:29
> > To: lab
> > Subject: ip pim autorp listerner
> >
> >
> > does anyone know what command replaces ip pim
> autorp listener in
> > 12.2?? or is there an equivelant?
> >
> > Regards,
> >
> > John D. Matus
> > MCSE, CCNP
> > 818.782.2061 office
> > 818.430.8372 mobile
> > jmatus@pacbell.net
> >
> >
>
This archive was generated by hypermail 2.1.4 : Sat Jul 03 2004 - 19:40:46 GMT-3