From: Sergio Jimenez Arguedas (sejimenez@its.co.cr)
Date: Fri May 14 2004 - 11:45:40 GMT-3
Hi Mohamed,
Let me Check!!!
Rgds,
Sergio
----- Original Message -----
From: "Mohamed" <nmohamed@cisco.com>
To: "'Sergio Jimenez Arguedas'" <sejimenez@its.co.cr>;
<ccielab@groupstudy.com>
Sent: Thursday, May 13, 2004 11:20 PM
Subject: RE: BGP METRIC!!! SET METRIC-TYPE INTERNAL!!!
> Hi,
>
> I checked it worked!.
> Here I don't know where is R6 ??
>
> Ospf Ebgp
> Up-------Down---------SFM
>
> See you have a OSPF route in Down with some cost.
> You have to run BGP in Down and redistribute ospf into BGP.
> You will get a BGP route in Down.
> The same route goes to SFM.
>
> Now change the cost in loop 0
> Down gets updated,BUT IT IS NOT SENDING TO SFM.
> Pls chk again.
>
> BTW-have you tried policy accounting ?
> Thanks
> Mohamed.
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Sergio Jimenez Arguedas
> Sent: Wednesday, May 12, 2004 9:42 PM
> To: ccielab@groupstudy.com
> Subject: BGP METRIC!!! SET METRIC-TYPE INTERNAL!!!
>
>
> Hi Alvaro and Mohamed,
>
>
> I read the explanation from Alvaro Retana, cisco!!!
>
>
> I tested it and it works fine without the ROUTE-MAP with the set
> metric-type internal!!!!
>
>
> Scenario:
>
> R1------------R2-------------------R3
>
>
>
> R1 and R2 ospf and R2 y R3 eBGP.
>
>
> R6#sh ip bgp
> BGP table version is 2, local router ID is 192.168.20.1
> Status codes: s suppressed, d damped, h history, * valid, > best, i -
> internal Origin codes: i - IGP, e - EGP, ? - incomplete
>
> Network Next Hop Metric LocPrf Weight Path
> *> 172.16.20.0/30 192.168.20.2 65 0 1 i
> _________________________________________________________________
>
>
> R3#sh ip bgp
> BGP table version is 3, local router ID is 192.168.20.1
> Status codes: s suppressed, d damped, h history, * valid, > best, i -
> internal Origin codes: i - IGP, e - EGP, ? - incomplete
>
> Network Next Hop Metric LocPrf Weight Path
> *> 172.16.20.0/30 192.168.20.2 164 0 1 i
>
>
>
> I changed the metric in the loop 0 of R1 from 1 to 100 and dinamically
> R2 changed the metric and send it to R3!!! So, The doubt with that CMD
> continue!!!
>
>
> Thanks for your time!!!
>
>
> Rgds,
>
>
>
> Sergio Jiminez A.
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Jun 02 2004 - 11:12:12 GMT-3