From: Cisco Sucks (lkgilles_ccie@yahoo.com.au)
Date: Fri Apr 30 2004 - 14:59:00 GMT-3
I think to send a break sequence over a TS you need to telnet to the router on the reverse telnet port of the box you are trying to break
Telnet: 10.10.10.254 port 2009
Amit Khopkar <akhopkar@yahoo.com> wrote:
hi group,
i am using a 2511 as terminal server. i have to acess some routers via this 2511.
when i open a reverse telnet to line 9
the router stops at
Trying R1 (1.1.1.1, 2009)... Open
if the relad the router connected to line 9 i can see the boot up sequence. i cannot send break to that router or enter it....
i have tried the following:
changing stopbits to 1
fixig tx and rx speeds to 9600
changing IOS (12.0, etc)
flowcontrol none
modem inout
modem printer
modem host
hyperterm, telnet and SecureCRT
no exec and transport input all commands are present
all routers can be accessed thru the console
ACC_SER#sh runn
Building configuration...
Current configuration:
!
version 11.2
no service password-encryption
no service udp-small-servers
no service tcp-small-servers
!
hostname ACC_SER
!
enable secret 5 $1$yChq$7mdBYUSBoNzsvNtGwP2U70
!
no ip domain-lookup
ip host R1 2009 1.1.1.1
!
interface Loopback0
ip address 1.1.1.1 255.255.255.255
!
interface Ethernet0
ip address 10.10.10.254 255.255.255.0
!
interface Serial0
no ip address
shutdown
no fair-queue
!
interface Serial1
no ip address
shutdown
!
no ip classless
!
!
line con 0
line 1 16
no exec
transport preferred telnet
transport input all
stopbits 1
line aux 0
line vty 0 4
password cisco
login
!
end
ACC_SER#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-J-L), Version 11.2(18), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 05-Apr-99 20:17 by jaturner
Image text-base: 0x0303F240, data-base: 0x00001000
ROM: System Bootstrap, Version 11.0(10c), SOFTWARE
BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c), RELEASE SOFTWARE (fc1)
ACC_SER uptime is 6 minutes
System restarted by reload
System image file is "flash:c2500-j-l_112-18.bin", booted via flash
cisco 2511 (68030) processor (revision M) with 14336K/2048K bytes of memory.
Processor board ID 15616375, with hardware revision 00000000
Bridging software.
SuperLAT software copyright 1990 by Meridian Technology Corp).
X.25 software, Version 2.0, NET2, BFE and GOSIP compliant.
TN3270 Emulation software.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
16 terminal line(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2102
ACC_SER#r1
Trying R1 (1.1.1.1, 2009)... Open
can anyone offer suggestions / solution
best rgds
amit
---------------------------------
Do you Yahoo!?
Win a $20,000 Career Makeover at Yahoo! HotJobs
This archive was generated by hypermail 2.1.4 : Mon May 03 2004 - 19:48:58 GMT-3