From: Richard Dumoulin (richard.dumoulin@vanco.es)
Date: Mon Mar 01 2004 - 17:55:10 GMT-3
I thought u just had to configure ppp callback request on one side and ppp
callback accept + a map-class dialer with callback username on the other
side, see below:
Rack1R5#sh run int d 1
Building configuration...
Current configuration : 256 bytes
!
interface Dialer1
ip address 1.1.1.2 255.0.0.0
encapsulation ppp
dialer pool 1
dialer remote-name cisco
dialer string 916600035
dialer-group 1
ppp callback request
ppp authentication chap
ppp chap hostname cisco1
ppp chap password 0 cisco
end
Rack1R5#sh run int bri 1/0
Building configuration...
Current configuration : 109 bytes
!
interface BRI1/0
no ip address
encapsulation ppp
dialer pool-member 1
isdn switch-type basic-net3
end
Rack1R4#sh run int d 1
Building configuration...
Current configuration:
!
interface Dialer1
ip address 1.1.1.1 255.0.0.0
encapsulation ppp
dialer pool 1
dialer string 916600085 class callback
dialer max-call 4096
dialer-group 1
ppp callback accept
ppp authentication chap
ppp chap hostname cisco
ppp chap password 7 060506324F41
end
Rack1R4#sh run | b map-class
map-class dialer callback
dialer callback-server username
Rack1R5#pi ip
Target IP address: 1.1.1.1
Repeat count [5]: 1
Datagram size [100]:
Timeout in seconds [2]:
Extended commands [n]:
Sweep range of sizes [n]:
Type escape sequence to abort.
Sending 1, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
1w0d: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 109 changed to up
1w0d: ISDN BR1/0: TX -> SETUP pd = 8 callref = 0x04
1w0d: Bearer Capability i = 0x8890
1w0d: Channel ID i = 0x83
1w0d: Called Party Number i = 0x80, '916600035', Plan:Unknown,
Type:Unknown
1w0d: ISDN BR1/0: RX <- CALL_PROC pd = 8 callref = 0x84
1w0d: Channel ID i = 0x89.
Success rate is 0 percent (0/1)
Rack1R5#
1w0d: ISDN BR1/0: RX <- CONNECT pd = 8 callref = 0x84
1w0d: %LINK-3-UPDOWN: Interface BRI1/0:1, changed state to up
1w0d: %DIALER-6-BIND: Interface BR1/0:1 bound to profile Di1
1w0d: BR1/0:1 PPP: Using dialer call direction
1w0d: BR1/0:1 PPP: Treating connection as a callout
1w0d: BR1/0:1 PPP: Phase is ESTABLISHING, Active Open [0 sess, 1 load]
1w0d: BR1/0:1 LCP: O CONFREQ [Closed] id 5 len 18
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x309034DD (0x0506309034DD)
1w0d: BR1/0:1 LCP: Callback 0 (0x0D0300)
1w0d: ISDN BR1/0: TX -> CONNECT_ACK pd = 8 callref = 0x04
1w0d: BR1/0:1 LCP: I CONFREQ [REQsent] id 6 len 15
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x5686114C (0x05065686114C)
1w0d: BR1/0:1 LCP: O CONFACK [REQsent] id 6 len 15
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x5686114C (0x05065686114C)
1w0d: BR1/0:1 LCP: I CONFACK [ACKsent] id 5 len 18
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x309034DD (0x0506309034DD)
1w0d: BR1/0:1 LCP: Callback 0 (0x0D0300)
1w0d: BR1/0:1 LCP: State is Open
1w0d: BR1/0:1 PPP: Phase is AUTHENTICATING, by both [0 sess, 1 load]
1w0d: BR1/0:1 CHAP: Using alternate hostname cisco1
1w0d: BR1/0:1 CHAP: O CHALLENGE id 9 len 27 from "cisco1"
1w0d: BR1/0:1 CHAP: I CHALLENGE id 167 len 26 from "cisco"
1w0d: BR1/0:1 CHAP: Using alternate hostname cisco1
1w0d: BR1/0:1 CHAP: O RESPONSE id 167 len 27 from "cisco1"
1w0d: BR1/0:1 CHAP: I SUCCESS id 167 len 4
1w0d: BR1/0:1 CHAP: I RESPONSE id 9 len 26 from "cisco"
1w0d: BR1/0:1 CHAP: O SUCCESS id 9 len 4
1w0d: ISDN BR1/0: RX <- DISCONNECT pd = 8 callref = 0x84
1w0d: Cause i = 0x8090 - Normal call clearing
1w0d: Display i = 'LIBERACION', 0x20, 'NORMAL'
1w0d: %ISDN-6-CONNECT: Interface BRI1/0:1 is now connected to 916600035
cisco
1w0d: %LINK-3-UPDOWN: Interface BRI1/0:1, changed state to down
1w0d: BR1/0:1 PPP: Phase is TERMINATING [0 sess, 1 load]
1w0d: BR1/0:1 LCP: State is Closed
1w0d: BR1/0:1 PPP: Phase is DOWN [0 sess, 1 load]
1w0d: %DIALER-6-UNBIND: Interface BR1/0:1 unbound from profile Di1
1w0d: ISDN BR1/0: TX -> RELEASE pd = 8 callref = 0x04
1w0d: Cause i = 0x8090 - Normal call clearing
1w0d: ISDN BR1/0: RX <- RELEASE_COMP pd = 8 callref = 0x84
Rack1R5#
Rack1R5#
1w0d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR1/0, TEI 109 changed to
down
1w0d: ISDN BR1/0: RX <- SETUP pd = 8 callref = 0x4D
1w0d: Sending Complete
1w0d: Bearer Capability i = 0x8890
1w0d: Channel ID i = 0x89
1w0d: Calling Party Number i = 0x01, 0x83, '916600035', Plan:ISDN,
Type:Unknown
1w0d: Called Party Number i = 0xA1, '916600085', Plan:ISDN,
Type:National
1w0d: ISDN BR1/0: Event: Received a DATA call from 916600035 on B1 at 64
Kb/s
1w0d: ISDN BR1/0: Event: Accepting the call id 0xC2
1w0d: %DIALER-6-BIND: Interface BR1/0:1 bound to profile Di1
1w0d: %LINK-3-UPDOWN: Interface BRI1/0:1, changed state to up
1w0d: BR1/0:1 PPP: Using dialer call direction
1w0d: BR1/0:1 PPP: Treating connection as a callin
1w0d: BR1/0:1 PPP: Phase is ESTABLISHING, Passive Open [0 sess, 1 load]
1w0d: BR1/0:1 LCP: State is Listen
1w0d: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 109 changed to up
Rack1R5#
1w0d: ISDN BR1/0: TX -> CALL_PROC pd = 8 callref = 0xCD
1w0d: Channel ID i = 0x89
1w0d: ISDN BR1/0: TX -> CONNECT pd = 8 callref = 0xCD
1w0d: ISDN BR1/0: RX <- CONNECT_ACK pd = 8 callref = 0x4D
1w0d: BR1/0:1 LCP: I CONFREQ [Listen] id 7 len 15
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x568652C5 (0x0506568652C5)
1w0d: BR1/0:1 LCP: O CONFREQ [Listen] id 6 len 15
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x30907666 (0x050630907666)
1w0d: BR1/0:1 LCP: O CONFACK [Listen] id 7 len 15
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x568652C5 (0x0506568652C5)
1w0d: BR1/0:1 LCP: I CONFACK [ACKsent] id 6 len 15
1w0d: BR1/0:1 LCP: AuthProto CHAP (0x0305C22305)
1w0d: BR1/0:1 LCP: MagicNumber 0x30907666 (0x050630907666)
1w0d: BR1/0:1 LCP: State is Open
1w0d: BR1/0:1 PPP: Phase is AUTHENTICATING, by both [0 sess, 0 load]
1w0d: BR1/0:1 CHAP: Using alternate hostname cisco1
1w0d: BR1/0:1 CHAP: O CHALLENGE id 10 len 27 from "cisco1"
1w0d: BR1/0:1 CHAP: I CHALLENGE id 168 len 26 from "cisco"
1w0d: BR1/0:1 CHAP: Waiting for peer to authenticate first
1w0d: BR1/0:1 CHAP: I RESPONSE id 10 len 26 from "cisco"
1w0d: BR1/0:1 CHAP: O SUCCESS id 10 len 4
1w0d: BR1/0:1 CHAP: Processing saved Challenge, id 168
1w0d: BR1/0:1 CHAP: Using alternate hostname cisco1
1w0d: BR1/0:1 CHAP: O RESPONSE id 168 len 27 from "cisco1"
1w0d: BR1/0:1 CHAP: I SUCCESS id 168 len 4
1w0d: BR1/0:1 PPP: Phase is UP [0 sess, 0 load]
1w0d: BR1/0:1 IPCP: O CONFREQ [Not negotiated] id 3 len 10
1w0d: BR1/0:1 IPCP: Address 1.1.1.2 (0x030601010102)
1w0d: BR1/0:1 CDPCP: O CONFREQ [Closed] id 3 len 4
1w0d: BR1/0:1 IPCP: I CONFREQ [REQsent] id 4 len 10
1w0d: BR1/0:1 IPCP: Address 1.1.1.1 (0x030601010101)
1w0d: BR1/0:1 IPCP: O CONFACK [REQsent] id 4 len 10
1w0d: BR1/0:1 IPCP: Address 1.1.1.1 (0x030601010101)
1w0d: BR1/0:1 CDPCP: I CONFREQ [REQsent] id 4 len 4
1w0d: BR1/0:1 CDPCP: O CONFACK [REQsent] id 4 len 4
1w0d: BR1/0:1 IPCP: I CONFACK [ACKsent] id 3 len 10
1w0d: BR1/0:1 IPCP: Address 1.1.1.2 (0x030601010102)
1w0d: BR1/0:1 IPCP: State is Open
1w0d: BR1/0:1 CDPCP: I CONFACK [ACKsent] id 3 len 4
1w0d: BR1/0:1 CDPCP: State is Open
1w0d: Di1 IPCP: Install route to 1.1.1.1
1w0d: %LINEPROTO-5-UPDOWN: Line protocol on Interface BRI1/0:1, changed
state to up
Rack1R5#
Rack1R5#pi 1.1.
1w0d: %ISDN-6-CONNECT: Interface BRI1/0:1 is now connected to 916600035
cisco
Rack1R5#pi 1.1.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 32/35/36 ms
HTH,
Richard
-----Mensaje original-----
De: Stefano Lassi [mailto:stefano.lassi@sysma.it]
Enviado el: lunes, 01 de marzo de 2004 21:25
Para: theoden@monmouth.com; ccielab@groupstudy.com
Asunto: RE: PPP Callback with Dialer Profiles
Thank you Theofanos
but, network connected to callback server is not supporting Caller-ID,
neither is ISDN ...
I'm looking for way to configure PPP callback (no Caller-ID) with Dialer
Profiles
Stefano
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
theoden@monmouth.com
Sent: lunedl 1 marzo 2004 19.03
To: Stefano Lassi; ccielab@groupstudy.com
Subject: Re: PPP Callback with Dialer Profiles
Hi, Stefano:
There is a section called "ISDN Caller ID Callback with Dialer Profiles
Examples" on the Cisco documentation CD. You can find it at:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fdia
l_c/fnsprt10/dafcalid.htm#1001156
Hope this helps.
Sincerely,
Theofanos
> Hi friends
>
>
> I would like configure ppp callback on two remote router already
configured to support DDR
with Dialer Profiles
>
> well, all Cisco examples seem to be oriented to Legacy DDR (whole
configuration on phycal
interface), no example with Dialer Profiles
>
>
> more modern examples by Cisco will involve Caller-ID
>
>
> well, I can't support it because callback server is not using ISDN but
Sync V.25bis
dialup, neither I have any way to screen incoming call, all PPP
authentication
>
>
> of course I can rollback DDR Dialer Profiles conf to DDR Legacy, but,
before doing:
>
>
>
>
> anybody has similar problem? anybody has got sany idea?
>
>
> Thank you very much in advance
>
>
> Stefano
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
---------------------------------------------
This message was sent using Monmouth Internet MI-Webmail.
http://www.monmouth.com/
This archive was generated by hypermail 2.1.4 : Thu Apr 01 2004 - 08:15:11 GMT-3