From: Brian McGahan (bmcgahan@internetworkexpert.com)
Date: Tue Feb 24 2004 - 17:55:36 GMT-3
Ram,
Why do you want to tag the native VLAN? Typically this is not
required unless you are doing .1q tunneling, which as of the latest release
the 2950 does not support. I would imagine that tagging of the native VLAN
will not be supported unless .1q tunneling is supported in future releases,
which is doubtful for this platform.
HTH,
Brian McGahan, CCIE #8593
bmcgahan@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
Toll Free: 877-224-8987 x 705
Outside US: 775-826-4344 x 705
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Ram Shummoogum
> Sent: Tuesday, February 24, 2004 11:32 AM
> To: Edwin Wargo
> Cc: ccielab@groupstudy.com
> Subject: Re: OT:Tag native VLAn on 2950
>
> Edwin:
>
> In 802.1Q by default ,all the vlans over a trunk are tagged except the
> native vlan. However, there are some platforms such as 3550 that allows
> you
> to tag the native vlan "vlan dot1q tag native". I am looking for the same
> thing on 2950.
>
>
>
> Regards,
>
>
>
> "Edwin Wargo" <edwin@rsquared.com>@groupstudy.com on 02/24/2004 12:03:18
> PM
>
> Please respond to "Edwin Wargo" <edwin@rsquared.com>
>
> Sent by: nobody@groupstudy.com
>
>
> To: Ram Shummoogum/Quebec/IBM@IBMCA, ccielab@groupstudy.com
> cc:
> Subject: Re: OT:Tag native VLAn on 2950
>
>
> Ram,
>
> The 2950 does support native VLAN tagging. Just be sure
> to use DOT1q as the protocol for trunking.
>
> Here's a sample configuration from a 2950 and a 7206:
>
> 2950
> ----
> interface FastEthernet0/8 <----Native VLAN
> switchport mode access
> no ip address
> !
> interface FastEthernet0/9
> switchport access vlan 102
> switchport mode access
> no ip address
> spanning-tree portfast
> !
> interface Vlan1
> ip address 192.168.98.215 255.255.255.0
> no ip route-cache
>
> 7206
> ----
> interface FastEthernet3/0
> no ip address
> duplex full
> !
> interface FastEthernet3/0.1
> encapsulation dot1Q 1 native
> ip address 192.168.98.1 255.255.255.0
> ip helper-address 192.168.100.31
> ip policy route-map internet-traffic-out
>
> HTH,
> Edwin
>
> On Tue, 24 Feb 2004 09:53:06 -0500
> Ram Shummoogum <rshummoo@ca.ibm.com> wrote:
> >Hi everyone:
> >
> >Can anyone tell me if native tagging is currently
> >supported on Cisco 2950
> >or will come in any future releases.
> >
> >
> >Regards,
> >RAM
> >
> >_______________________________________________________________________
> >Please help support GroupStudy by purchasing your study
> >materials from:
> >http://shop.groupstudy.com
> >
> >Subscription information may be found at:
> >http://www.groupstudy.com/list/CCIELab.html
>
> This email was scanned for viruses by RAV AntiVirus.
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
> _______________________________________________________________________
> Please help support GroupStudy by purchasing your study materials from:
> http://shop.groupstudy.com
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Fri Mar 05 2004 - 07:13:56 GMT-3