From: Snow, Tim (timothy.snow@eds.com)
Date: Tue Oct 07 2003 - 05:22:04 GMT-3
Router#sh ver | inc 2500 Software
IOS (tm) 2500 Software (C2500-JOS56I-L), Version 12.1(5)T10, RELEASE
SOFTWARE (
fc2)
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#map-class frame test
Router(config-map-class)#frame cir 128000
Router(config-map-class)#frame bc 1280
Router(config-map-class)#frame frag 80
Router(config-map-class)#frame fair
Router(config-map-class)#
Router#sh ru
2d16h: %SYS-5-CONFIG_I: Configured from console by consolen | b map-class
map-class frame-relay test
frame-relay cir 128000
frame-relay bc 1280
no frame-relay adaptive-shaping
frame-relay fair-queue
frame-relay fragment 80
dialer-list 1 protocol ip permit
!
!
line con 0
transport input none
line aux 0
line vty 0 4
!
End
Looks like an IOS thing bro. Might want to check the Feature Navigator
Tim
-----Original Message-----
From: Ken.Farrington@barclayscapital.com
[mailto:Ken.Farrington@barclayscapital.com]
Sent: Tuesday, October 07, 2003 3:53 AM
To: ccielab@groupstudy.com
Subject: FRF12 (FRTS command)
Guys, on the univercd I see the frame-relay fragment command but cant seem
to implement it on any of my routers. Used a 2600 with the following
R2#sh hard
Cisco Internetwork Operating System Software
IOS (tm) C2600 Software (C2600-IX-M), Version 12.2(17a), RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
and various other IOSs
Can anyone advise?
Router(config)# map-class frame-relay frag
Router(config-map-class)# frame-relay cir 128000
Router(config-map-class)# frame-relay bc 1280
Router(config-map-class)# frame-relay fragment 40
Router(config-map-class)# frame-relay fair-queue
all the command i get are
R2(config)#map-class frame-relay ken
R2(config-map-class)#frame
R2(config-map-class)#frame-relay ?
adaptive-shaping Adaptive traffic rate adjustment, Default = none
bc Committed burst size (Bc), Default = 56000 bits
be Excess burst size (Be), Default = 0 bits
cir Committed Information Rate (CIR), Default = 56000 bps
congestion Congestion management parameters
custom-queue-list VC custom queueing
end-to-end Configure frame-relay end-to-end VC parameters
fair-queue VC fair queueing
fecn-adapt Enable Traffic Shaping reflection of FECN as BECN
holdq Hold queue size for VC
interface-queue PVC interface queue parameters
mincir Minimum acceptable CIR, Default = CIR/2 bps
priority-group VC priority queueing
tc Policing Measurement Interval (Tc)
traffic-rate VC traffic rate
R2(config-map-class)#frame-relay
------------------------------------------------------------------------
For more information about Barclays Capital, please
visit our web site at http://www.barcap.com.
Internet communications are not secure and therefore the Barclays
Group does not accept legal responsibility for the contents of this
message. Although the Barclays Group operates anti-virus programmes,
it does not accept responsibility for any damage whatsoever that is
caused by viruses being passed. Any views or opinions presented are
solely those of the author and do not necessarily represent those of the
Barclays Group. Replies to this email may be monitored by the Barclays
Group for operational or business reasons.
------------------------------------------------------------------------
***Get your CCIE and a FREE vacation: Shop.GroupStudy.com***
This archive was generated by hypermail 2.1.4 : Mon Nov 24 2003 - 07:52:58 GMT-3