From: wsq (wsqccie@hotmail.com)
Date: Mon Sep 08 2003 - 07:33:49 GMT-3
I think you shoul d change the ospf or Eigrp distance which ospf's is better
----- Original Message -----
From: "Chen Kwong Wai William" <kwchen@netvigator.com>
To: "Jonathan V Hays" <jhays@jtan.com>; <ccielab@groupstudy.com>
Sent: Sunday, September 07, 2003 11:14 AM
Subject: Re: Lab Scenario about OSPF nad EIGRP mutual redistribution, Please comment.
> Hi,
>
> But for this case, will you configure to make R3 prefer R2 for the route
> to R4?
>
> --- William
>
> ----- Original Message -----
> From: "Jonathan V Hays" <jhays@jtan.com>
> To: "'Chen Kwong Wai William'" <kwchen@netvigator.com>;
> <ccielab@groupstudy.com>
> Sent: Sunday, September 07, 2003 2:45 AM
> Subject: RE: Lab Scenario about OSPF nad EIGRP mutual redistribution, Please
> comment.
>
>
> You will have to perform configurations that are not specified exactly,
> in order to get meet the lab requirements.
>
> From what I've seen, you will not lose points in the CCIE lab for
> overconfiguring, unless your extra configuration breaks a requirement or
> unless the particular extra configuration steps are prohibited (e.g.,
> static routes).
>
> HTH,
>
> Jonathan
>
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Chen Kwong Wai William
> Sent: Saturday, September 06, 2003 1:51 PM
> To: ccielab@groupstudy.com
> Subject: Lab Scenario about OSPF nad EIGRP mutual redistribution, Please
> comment.
>
>
> Dear all,
>
> R4
> | |
> |- R2 --------- R1
> | |
> | |
> |- R3 ---------- |
> |
>
> I think it is quite a common scenario in Lab, Suppose
> R1, R2, R3 (a point-to-multipoint network)is connected \
> by frame relay and runs in OSPF backbone. R2, R3 is also
> connected by Fast Ethernet and runs EIGRP. Finally,
> R2, R4 is connected by Serial Point-to-point line and
> runs in OSPF non-backbone area.
>
> After mutual redistribution in R2 and R3 and proper
> filter to prevent route feedback. You may find that
> R3 is prefer R1 as a next-hop to reach R4, becuase
> OSPF is prefer than external EIGRP routes.
>
> My question is if you are not ask to do any configuration
> to make R3 to prefer R2 as next-hop to go the R4 in the
> lab, will you do it? Will this additional work make you
> lose marks in lab. Do you think to prefer OSPF backbone
> is a normal situation or not?
>
> Sorry for my poor ASCII drawing.
>
> - William
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Oct 01 2003 - 07:24:24 GMT-3