From: Alec (clapun@graduate.hku.hk)
Date: Thu Sep 04 2003 - 12:33:48 GMT-3
thanks Brian..
If the digit '4' or '44' is input, which one will be matched ? dial-peer 3
or 4 ? In fact, just want to know if dial-peer 3 can be used as default
route for voice as well.
regards,
alec
----- Original Message -----
From: "Brian Dennis" <bdennis@internetworkexpert.com>
To: "'Alec'" <clapun@graduate.hku.hk>
Cc: <ccielab@groupstudy.com>
Sent: Thursday, September 04, 2003 12:06 PM
Subject: RE: Destination pattern symbols
> Alec,
> Here is how they would match.
>
> CSIM Start
> 1) "1" - dial-peer 1
> 2) "12" - dial-peer 2
> 3) "123" - dial-peer 2
>
> Phone
> 1) "1" - dial-peer 1
> 2) "12" - dial-peer 1
> 3) "123" - dial-peer 1
>
> Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
> bdennis@internetworkexpert.com
> Toll Free: 877-334-8987
> Direct: 775-745-6404 (Outside the US and Canada)
> Internetwork Expert, Inc.
> http://www.InternetworkExpert.com
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Alec
> Sent: Wednesday, September 03, 2003 8:14 PM
> To: Brian McGahan; 'Paul Chen'; ccielab@groupstudy.com
> Subject: Re: Destination pattern symbols
>
> thanks Brian. If I have the following dial-peer voice command, which
> one
> will be used after I pressed
>
> 1) "1"
> 2) "12"
> 3) "123"
>
> in a real phone and csim ? Thanks.
>
> dial-peer voice 1 voip
> destination-pattern 1
> session target ipv4:10.0.0.1
> !
> dial-peer voice 2 voip
> destination-pattern 12
> session target ipv4:10.0.0.1
> !
> dial-peer voice 3 voip
> destination-pattern .
> session target ipv4:20.0.0.2
> !
> dial-peer voice 4 voip
> destination-pattern .T
> session target ipv4:20.0.0.2
>
>
> ----- Original Message -----
> From: "Brian McGahan" <bmcgahan@internetworkexpert.com>
> To: "'Alec'" <clapun@graduate.hku.hk>; "'Paul Chen'"
> <cpjchen@starhub.net.sg>; <ccielab@groupstudy.com>
> Sent: Thursday, September 04, 2003 2:20 AM
> Subject: RE: Destination pattern symbols
>
>
> > Alec,
> >
> > It will only match a single character then. As soon as the
> > single character is input, the router will do call setup. This will
> not
> > be true for the 'csim start' command though, since the string is sent
> > all at once. From an actual phone though, the string is sent 1
> > character at a time.
> >
> > HTH
> >
> > Brian McGahan, CCIE #8593
> > bmcgahan@internetworkexpert.com
> >
> > Internetwork Expert, Inc.
> > http://www.InternetworkExpert.com
> > Toll Free: 877-334-8987
> > Direct: 708-362-1418 (Outside the US and Canada)
> >
> >
> > -----Original Message-----
> > From: Alec [mailto:clapun@graduate.hku.hk]
> > Sent: Wednesday, September 03, 2003 10:24 AM
> > To: Brian McGahan; 'Paul Chen'; ccielab@groupstudy.com
> > Subject: Re: Destination pattern symbols
> >
> > So what if I use destination-pattern . for voice default route ?
> What's
> > the
> > difference with .T ?
> >
> > ----- Original Message -----
> > From: "Brian McGahan" <bmcgahan@internetworkexpert.com>
> > To: "'Paul Chen'" <cpjchen@starhub.net.sg>; <ccielab@groupstudy.com>
> > Sent: Wednesday, September 03, 2003 4:22 PM
> > Subject: RE: Destination pattern symbols
> >
> >
> > > Paul,
> > >
> > > T actually means interdigit timeout. The default interdigit
> > > timeout is 10 seconds. Each time you dial a digit, the router is
> > going
> > > to wait 10 seconds before doing call setup. After 10 seconds have
> > > expired, the router assumes that what you have entered so far is the
> > > complete dial string, and does call setup on those digits. You can
> > > modify the interdigit timeout with the voice-port command 'timeouts
> > > inter-digit'.
> > >
> > > The combination of the . (any single character) and the T (wait
> > > for additional characters) effectively defines a default route for
> > > voice.
> > >
> > >
> > > HTH,
> > >
> > > Brian McGahan, CCIE #8593
> > > bmcgahan@internetworkexpert.com
> > >
> > > Internetwork Expert, Inc.
> > > http://www.InternetworkExpert.com
> > > Toll Free: 877-334-8987
> > > Direct: 708-362-1418 (Outside the US and Canada)
> > >
> > >
> > > -----Original Message-----
> > > From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf
> > Of
> > > Paul Chen
> > > Sent: Wednesday, September 03, 2003 3:05 AM
> > > To: ccielab@groupstudy.com
> > > Subject: Destination pattern symbols
> > >
> > > Hi,
> > >
> > >
> > >
> > > Could someone please explain to me what these symbols mean:
> > >
> > >
> > >
> > > Destination-pattern .T
> > >
> > >
> > >
> > > A dot implies a single character right ?
> > >
> > >
> > >
> > > The T symbol implies a variable length dial string.
> > >
> > >
> > >
> > > Does the combination of the 2 symbols mean dial any number ?
> > >
> > >
> > >
> > > Thanks.
> > >
> > > Paul
> > >
> > >
> > >
> >
> _______________________________________________________________________
> > > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> > >
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> > >
> > >
> > >
> >
> _______________________________________________________________________
> > > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> > >
> > > Subscription information may be found at:
> > > http://www.groupstudy.com/list/CCIELab.html
> >
> >
> >
> _______________________________________________________________________
> > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
> >
> > Subscription information may be found at:
> > http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Oct 01 2003 - 07:24:23 GMT-3