From: pauldongso (pauldongso@hotmail.com)
Date: Tue Aug 26 2003 - 09:33:02 GMT-3
If static route is allowed, use floating static route, one point to
1.1.1.1, the other pointing to 1.1.1.2 with higher distance.
If static route is not allowed, your suggestion is right, make 3550 run
IGP so that it can learn all alternative paths.
Paul
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
E03k
Sent: Tuesday, 26 August 2003 10:49 AM
To: Peng Zheng; boby2kusa@hotmail.com; wwwjjang@chol.com;
ccielab@groupstudy.com
Subject: (Re): Re: Cat 3550's SVI-Question!!
Hi..Peng
Thanks for your kind reply..
I agree with your saying about using HSRP..
(It's Trivial).
But HSRP makes R1 & R2 be configured !!
"I want to set up the configuration on Cat3550 ONLY !!!!"
Thasnk..
--- Original Message ---
:83=@L(From): "Peng Zheng" zpnist@yahoo.com
9^4B@L(To): boby2kusa@hotmail.com, wwwjjang@chol.com,
ccielab@groupstudy.com
:83=@O=C(Date): Mon, 25 Aug 2003 10:27:32 -0700 (PDT)
A&8q(Subject): Re: Cat 3550's SVI-Question!!
Why not HSRP?
--- boby2kusa@hotmail.com wrote:
> Pretty please?!?
> ----- Original Message -----
> From: <wwwjjang@chol.com>
> To: <ccielab@groupstudy.com>
> Sent: Monday, August 25, 2003 1:50 AM
> Subject: Cat 3550's SVI-Question!!
>
>
> > Hi..everyone..
> >
> > I have no cat3550 switch. so i don't test this
> configuration..
> > So, The people who has a catalyst 3550 help me
> solve this problom..
> >
> > Thanks..
> >
> > --------
> > Diagram
> > --------
> >
> > (s0)-R1-(e0 1.1.1.1)-(Fa0/1)-Cat3550--(Fa0/2)-(e0
> 1.1.1.2)--R2-(s0)
> >
> > -Cat 3550's Fa0/1 & Fa0/2 is included in Vlan 100.
> > -Cat 3550's IP is 1.1.1.3/24
> > -R1's E0 & R2's E0 is in OSPF-Area 1
> > -R1's & R2'S0 is in OSPF-Area0
> >
> > ---------
> > Question
> > ---------
> >
> > If One of the R1 & R2's Ethenet-interfaces goes
> down,
> > Make sure Cat3550 has an alternate route..!!
> >
> > ------------
> > My solution
> > ------------
> > -If i use a Default-gateway configuration , It's
> not an answer
> > (Because it does not give an alternate route..)
> > - i think i must use a L3-interface, So
> > I put the "SVI 100-interfaces in the
> OSPF-Process" => is it right ??
> >
> > ip routing
> > !
> > interface vlan 100
> > ip address 1.1.1.3 255.255.255.0
> > !
> > router ospf 1
> > network 1.1.1.3 0.0.0.0 area 1
> >
> >
> >
>
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:54:07 GMT-3