From: Charles Church (cchurch@wamnet.com)
Date: Thu Aug 14 2003 - 14:17:36 GMT-3
John,
A simple thing to do might be to put an IPSec image on the term server, and
do SSH to it. It'll only be SSH 1.0/1.5, but it's a lot better than raw
telnet.
Chuck Church
CCIE #8776, MCNE, MCSE
Wam!Net Government Services
13665 Dulles Technology Dr. Ste 250
Herndon, VA 20171
Office: 703-480-2569
Cell: 703-819-3495
cchurch@wamnet.com
PGP key: http://pgp.mit.edu:11371/pks/lookup?search=chuck+church&op=index
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com]On Behalf Of
John Matijevic
Sent: Thursday, August 14, 2003 12:51 PM
To: Dennis Laganiere; 'Jason Westlund'; ccielab@groupstudy.com
Subject: Re: putting rack on internet
Hello Team,
Thanks for everyones response, I am going to setup my comm server with a
static ip on the ethernet, then setup my NAT on my dsl router to port
forward telnet and translate to static ip of my comm server.
Sincerely,
Matijevic
----- Original Message -----
From: "Dennis Laganiere" <dennisl@advancedbionics.com>
To: "'Jason Westlund'" <jason.westlund@nmwco.com>; "John Matijevic"
<matijevi@bellsouth.net>; <ccielab@groupstudy.com>
Sent: Thursday, August 14, 2003 12:17 PM
Subject: RE: putting rack on internet
> I simply setup my netgear to forward telnet traffic from outside to the IP
> address of my terminal server (2511), and that worked great.
>
> Good luck...
>
> --- Dennis
>
> -----Original Message-----
> From: Jason Westlund [mailto:jason.westlund@nmwco.com]
> Sent: Thursday, August 14, 2003 9:11 AM
> To: John Matijevic; ccielab@groupstudy.com
> Subject: RE: putting rack on internet
>
> John,
>
> Do you have NAT device to use? I have configured a NetGear WebSafer
> router to allow PCAnywhere traffic to a specific server. From there I
> can access my entire network and lab gear through the comm Server.
>
> I hope this helps.
>
> -Jason
>
>
>
>
>
> -----Original Message-----
> From: John Matijevic [mailto:matijevi@bellsouth.net]
> Sent: Thursday, August 14, 2003 8:19 AM
> To: ccielab@groupstudy.com
> Subject: putting rack on internet
>
> Hello Team,
> I am trying to setup my routers so I can access remotely via internet. I
> have
> a Wirespeed- Westell dsl router at home, where I have a static ip
> address
> assigned to it. I cannot get anymore static ip addresses as I have a
> residential plan from BellSouth. I am not sure how to get this working I
> have
> attempted to try to use passthru to pass the IP to my comm server. If
> anyone
> could help me get this working, would be greatly appreciated.
> Sincerely,
> Matijevic
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:53:59 GMT-3