From: Jeongwoo Park (jpark@wams.com)
Date: Sat Aug 09 2003 - 20:45:26 GMT-3
Could it be applied to Serial interface?
I have a same ios version. It doesn't seem to have an option for serial
interface.
r1(config-if)#isis ?
adjacency-filter Filter IS-IS adjacencies
authentication ISIS authentication for interface related
PDUs
circuit-type Configure circuit type for interface
csnp-interval Set CSNP interval in seconds
hello Add padding to IS-IS hello packets
hello-interval Set Hello interval in seconds
hello-multiplier Set multiplier for Hello holding time
ipv6 IPv6 interface configuration
lsp-interval Set LSP transmission interval
mesh-group Set ISIS mesh group
metric Configure the metric for interface
password Configure the authentication password for
interface
priority Set priority for Designated Router election
retransmit-interval Set per-LSP retransmission interval
retransmit-throttle-interval Set interface LSP retransmission interval
three-way-handshake Select Cisco or IETF three-way handshake
-----Original Message-----
From: Brian Dennis [mailto:bdennis@internetworkexpert.com]
Sent: Friday, August 08, 2003 2:35 PM
To: groupstudy@cconlinelabs.com
Cc: ccielab@groupstudy.com
Subject: RE: Re[2]: ISIS over Frame Relay
c2600-j1s3-mz.122-15.T5.bin
ENTERPRISE BASIC
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
-----Original Message-----
From: Tony Schaffran [mailto:groupstudy@cconlinelabs.com]
Sent: Friday, August 08, 2003 2:19 PM
To: 'Brian Dennis'; 'badger'
Cc: ccielab@groupstudy.com
Subject: RE: Re[2]: ISIS over Frame Relay
There is a bit of conflict in that document. It says it was introduced
in
12.2.(8)T and it is supported on the 2600's, but the T code does not go
that
high for the 2600's.
Am I missing something?
Tony Schaffran
Network Analyst
CCIE #11071
CCNP, CCNA, CCDA
NNCDS, NNCSS, CNE, MCSE
http://www.cconlinelabs.com/
Your #1 choice for online cisco rack rentals.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Brian Dennis
Sent: Friday, August 08, 2003 1:38 PM
To: 'badger'
Cc: ccielab@groupstudy.com
Subject: RE: Re[2]: ISIS over Frame Relay
12.2(8)T
http://www.cisco.com/en/US/products/sw/iosswrel/ps1839/products_feature_
guide09186a0080087cb8.html
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
bdennis@internetworkexpert.com
Internetwork Expert, Inc.
http://www.InternetworkExpert.com
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
badger
Sent: Friday, August 08, 2003 1:31 PM
To: Thomas Larus
Cc: John Matijevic; Adam Asay; ccielab@groupstudy.com
Subject: Re[2]: ISIS over Frame Relay
Hello Thomas,
Friday, August 8, 2003, 10:35:46 AM, you wrote:
TL> Try playing around with the relatively new IOS feature of setting
the IS-IS
TL> network type. An old solution was to use tunnels, but now you can
actually
TL> set the IS-IS network type to multipoint just like you can in OSPF.
TL> Check it out. It's pretty cool.
What version of code might that be in?
-- Best regards, badger mailto:badger@pongo.org
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:53:56 GMT-3