From: Yuki Hisano (yukyhisano@hotmail.com)
Date: Thu Aug 07 2003 - 12:29:23 GMT-3
Matijevic,
I beleive it will solve the issue.
I just wanna know why and whats wrong with 0x102
Thanks!
Yuki
----- Original Message -----
From: "John Matijevic" <matijevi@bellsouth.net>
To: "Yuki Hisano" <yukyhisano@hotmail.com>; "Jim Dixon"
<JDixon@communigroup.com>; <ccielab@groupstudy.com>
Sent: Thursday, August 07, 2003 11:24 AM
Subject: Re: Break-key & _continue_
Hello Yuki,
The reason you cant login, is because its not a public document, there are
some sections on Cisco's website thats only accessable if you are a cisco
reseller. I am very confident that the suggestion I gave you will solve your
issue.
Sincerely,
Matijevic
----- Original Message -----
From: "Yuki Hisano" <yukyhisano@hotmail.com>
To: "Jim Dixon" <JDixon@communigroup.com>; "John Matijevic"
<matijevi@bellsouth.net>; <ccielab@groupstudy.com>
Sent: Thursday, August 07, 2003 11:19 AM
Subject: Re: Break-key & _continue_
> I cant log in the link below.
>
> ??
>
> Yuki
>
> ----- Original Message -----
> From: "Jim Dixon" <JDixon@communigroup.com>
> To: "'Yuki Hisano'" <yukyhisano@hotmail.com>; "John Matijevic"
> <matijevi@bellsouth.net>; <ccielab@groupstudy.com>
> Sent: Thursday, August 07, 2003 11:03 AM
> Subject: RE: Break-key & _continue_
>
>
>
http://www.cisco.com/en/US/customer/products/hw/switches/ps708/prod_release_
> note09186a008015c76a.html
> 0x2102 should be correct for autoboot
> per the excerpt below from the link above.
> Upgrading a Nonredundant Configuration
>
> --------------------------------------------------------------------------
-- > ---- > Step 1 As a precaution, save the system configuration. > > Step 2 Copy the Cisco IOS system software image (for example, > c6sup12-jsv-mz.121-8b.EX5 or later) to either sup-bootflash or slot0. > > Step 3 Remove the old boot commands: > > Router(config)# no boot system flash slot0:old_image_name > or: > > Router(config)# no boot system flash sup-bootflash:old_image_name > Step 4 Configure the switch to autoboot the new image: > > > -------------------------------------------------------------------------- -- > ---- > Note To avoid boot failure, include the device name (slot0 or > sup-bootflash) in the following commands. > > -------------------------------------------------------------------------- -- > ---- > > Router(config)# boot system flash slot0:c6sup12-jsv-mz.121-8b.EX5 > or: > > Router(config)# boot system flash sup-bootflash:c6sup12-jsv-mz.121-8b.EX5 > Step 5 Set the configuration register parameter to autoboot: > > Router(config)# config-register 0x2102 > Step 6 Copy the running configuration to the startup configuration in > NVRAM: > > Router# write memory > Step 7 Reload the switch: > > Router# reload > > -----Original Message----- > From: Yuki Hisano [mailto:yukyhisano@hotmail.com] > Sent: Thursday, August 07, 2003 09:54 > To: John Matijevic; ccielab@groupstudy.com > Subject: Re: Break-key & _continue_ > > > John, Joe, > > It is 0x102. > Is this OK? > > Thanks! > > Yuki > ----- Original Message ----- > From: "John Matijevic" <matijevi@bellsouth.net> > To: "Yuki Hisano" <yukyhisano@hotmail.com>; <ccielab@groupstudy.com> > Sent: Wednesday, August 06, 2003 6:05 PM > Subject: Re: Break-key & _continue_ > > > Yuki, > I had a similar experience take a look at your config register and make sure > that its set to 2102. > You can do a sh ver, also if you need to you may need to change using the > config command. > Sincerely, > Matijevic > ----- Original Message ----- > From: "Yuki Hisano" <yukyhisano@hotmail.com> > To: <ccielab@groupstudy.com> > Sent: Wednesday, August 06, 2003 5:11 PM > Subject: Break-key & _continue_ > > > > Hi, > > > > I have a 7603 router that is acting funny. > > A while ago, someone rebooted the router remotely. It started to restart > > over and over till the command "continue" was entered after the break key. > > It just happened again when we try to upgrade the code and memory. > > This time, the procedure did not help and had to put everything in the way > > it wasand enered > > "cotinue". > > > > I am worried that if this happens again. > > > > Anyone has any solution to this? > > > > Thanks! > > > > Yuki > > > > > > _______________________________________________________________________ > > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group. > > > > Subscription information may be found at: > > http://www.groupstudy.com/list/CCIELab.html > > > _______________________________________________________________________ > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group. > > Subscription information may be found at: > http://www.groupstudy.com/list/CCIELab.html > > > _______________________________________________________________________ > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group. > > Subscription information may be found at: > http://www.groupstudy.com/list/CCIELab.html > > > _______________________________________________________________________ > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group. > > Subscription information may be found at: > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:53:54 GMT-3