From: Yuki Hisano (yukyhisano@hotmail.com)
Date: Thu Aug 07 2003 - 12:19:59 GMT-3
I cant log in the link below.
??
Yuki
----- Original Message -----
From: "Jim Dixon" <JDixon@communigroup.com>
To: "'Yuki Hisano'" <yukyhisano@hotmail.com>; "John Matijevic"
<matijevi@bellsouth.net>; <ccielab@groupstudy.com>
Sent: Thursday, August 07, 2003 11:03 AM
Subject: RE: Break-key & _continue_
http://www.cisco.com/en/US/customer/products/hw/switches/ps708/prod_release_
note09186a008015c76a.html
0x2102 should be correct for autoboot
per the excerpt below from the link above.
Upgrading a Nonredundant Configuration
----------------------------------------------------------------------------
---- Step 1 As a precaution, save the system configuration.Step 2 Copy the Cisco IOS system software image (for example, c6sup12-jsv-mz.121-8b.EX5 or later) to either sup-bootflash or slot0.
Step 3 Remove the old boot commands:
Router(config)# no boot system flash slot0:old_image_name or:
Router(config)# no boot system flash sup-bootflash:old_image_name Step 4 Configure the switch to autoboot the new image:
---------------------------------------------------------------------------- ---- Note To avoid boot failure, include the device name (slot0 or sup-bootflash) in the following commands.
---------------------------------------------------------------------------- ----
Router(config)# boot system flash slot0:c6sup12-jsv-mz.121-8b.EX5 or:
Router(config)# boot system flash sup-bootflash:c6sup12-jsv-mz.121-8b.EX5 Step 5 Set the configuration register parameter to autoboot:
Router(config)# config-register 0x2102 Step 6 Copy the running configuration to the startup configuration in NVRAM:
Router# write memory Step 7 Reload the switch:
Router# reload
-----Original Message----- From: Yuki Hisano [mailto:yukyhisano@hotmail.com] Sent: Thursday, August 07, 2003 09:54 To: John Matijevic; ccielab@groupstudy.com Subject: Re: Break-key & _continue_
John, Joe,
It is 0x102. Is this OK?
Thanks!
Yuki ----- Original Message ----- From: "John Matijevic" <matijevi@bellsouth.net> To: "Yuki Hisano" <yukyhisano@hotmail.com>; <ccielab@groupstudy.com> Sent: Wednesday, August 06, 2003 6:05 PM Subject: Re: Break-key & _continue_
Yuki, I had a similar experience take a look at your config register and make sure that its set to 2102. You can do a sh ver, also if you need to you may need to change using the config command. Sincerely, Matijevic ----- Original Message ----- From: "Yuki Hisano" <yukyhisano@hotmail.com> To: <ccielab@groupstudy.com> Sent: Wednesday, August 06, 2003 5:11 PM Subject: Break-key & _continue_
> Hi, > > I have a 7603 router that is acting funny. > A while ago, someone rebooted the router remotely. It started to restart > over and over till the command "continue" was entered after the break key. > It just happened again when we try to upgrade the code and memory. > This time, the procedure did not help and had to put everything in the way > it wasand enered > "cotinue". > > I am worried that if this happens again. > > Anyone has any solution to this? > > Thanks! > > Yuki > > > _______________________________________________________________________ > You are subscribed to the GroupStudy.com CCIE R&S Discussion Group. > > Subscription information may be found at: > http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Tue Sep 02 2003 - 18:53:54 GMT-3