RE: redistribution between ospf and rip2

From: Mustafa Bayramov (ICT/IT) (mustafa@azercell.com)
Date: Tue Jul 22 2003 - 19:02:14 GMT-3

Next message: Jim Phillipo: "Syslog Messages for IOS"
Previous message: Jonathan V Hays: "RE: redistribution between ospf and rip2"
Maybe in reply to: Banlan Chen: "redistribution between ospf and rip2"
Next in thread: ccie2be: "Re: redistribution between ospf and rip2"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

Also check your IOS versions I remember IOS 12.1.X had bug related to
tagging RIPv2.

Regards

Mustafa M Bayramov

CISSP
CCNP,CCDP,Cisco Security Specialist
Network engineer and security analyst

"I know nothing except the fact of my ignorance." Socrates

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Jonathan V Hays
Sent: Tuesday, July 22, 2003 4:49 PM
To: 'Banlan Chen'; ccielab@groupstudy.com
Subject: RE: redistribution between ospf and rip2

Try assigning default metrics.

-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Banlan Chen
Sent: Tuesday, July 22, 2003 4:08 PM
To: ccielab@groupstudy.com
Subject: redistribution between ospf and rip2

Hi All,

I am tring to mutual redistribute ospf and rip2 with tag, but it doesn't
work. from RIP side I can see the ospf routes, but at ospf side I can't
see any routes from RIP. Could someone figure out what's problem in my
configuration. Thanks a lot.

interface Loopback0
ip address 150.50.6.6 255.255.255.255
!
interface Ethernet0
ip address 150.50.100.6 255.255.255.0
!
interface Serial0
ip address 150.50.10.6 255.255.255.0
encapsulation frame-relay
ip ospf network point-to-point
frame-relay map ip 150.50.10.2 421 broadcast
frame-relay map ip 150.50.10.6 421
frame-relay lmi-type ansi
!
router ospf 1
log-adjacency-changes
redistribute rip subnets route-map rip-os
network 150.50.6.6 0.0.0.0 area 0
network 150.50.10.0 0.0.0.255 area 0
!
router rip
version 2
redistribute ospf 1 metric 1 route-map os-rip
passive-interface default
no passive-interface Ethernet0
network 150.50.0.0
!
route-map os-rip deny 10
match tag 120
!
route-map os-rip permit 20
set tag 110
!
route-map rip-os deny 10
match tag 110
!
route-map rip-os permit 20
set tag 120

--
--------- Original Message ---------
DATE: Fri, 18 Jul 2003 19:19:11
From: "Banlan Chen" <banlan.chen@lycos.com>
To: ccielab@groupstudy.com
Cc: 
>Hi Group,
>
>When I configure RIP over two FR main interfaces, I should enable
split-horizon on each interface or just enable it at one of these
interfaces.
>Under ATM interface, Do I need configure ip split-horizon for RIP and
EIGRP?
>Thanks in advance.
>
>Banlan
>
>
>____________________________________________________________
>Get advanced SPAM filtering on Webmail or POP Mail ... Get Lycos Mail!
>http://login.mail.lycos.com/r/referral?aid=27005
>
>
>_______________________________________________________________________
>You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
>Subscription information may be found at: 
>http://www.groupstudy.com/list/CCIELab.html
>

Next message: Jim Phillipo: "Syslog Messages for IOS"
Previous message: Jonathan V Hays: "RE: redistribution between ospf and rip2"
Maybe in reply to: Banlan Chen: "redistribution between ospf and rip2"
Next in thread: ccie2be: "Re: redistribution between ospf and rip2"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ] [ attachment ]

This archive was generated by hypermail 2.1.4 : Wed Aug 06 2003 - 06:52:49 GMT-3