From: Sam Munzani (sam@munzani.com)
Date: Tue Jul 15 2003 - 17:46:00 GMT-3
Very handly command to figure out if a certain OID is supported by your
running IOS. Otherwise you have to dig up CCO for that info.
Sam
> You can also view a limited amount of information on the router itself
> using the hidden command "show snmp mib".
>
> Rack5R6(config)#snmp community public ro
> Rack5R6(config)#^Z
> Rack5R6#term len 0
> Rack5R6#show snmp mib | in atm
> atmInterfaceConfEntry.1
> atmInterfaceConfEntry.2
> atmInterfaceConfEntry.3
> atmInterfaceConfEntry.4
> atmInterfaceConfEntry.5
> atmInterfaceConfEntry.6
> atmInterfaceConfEntry.7
> atmInterfaceConfEntry.8
> atmInterfaceConfEntry.9
> atmInterfaceConfEntry.10
> atmInterfaceConfEntry.11
> atmInterfaceConfEntry.12
> atmTrafficDescrParamEntry.2
> atmTrafficDescrParamEntry.3
> atmTrafficDescrParamEntry.4
> atmTrafficDescrParamEntry.5
> <snip>
> Rack5R6#
>
> To get more detail use the link below and put the value in.
> http://www.cisco.com/pcgi-bin/Support/Mibbrowser/unity.pl?tab=2
>
> Example:
> http://www.cisco.com/pcgi-bin/Support/Mibbrowser/unity.pl?f=Translate&g=
> atmInterfaceConfEntry.1&submit=Translate
>
> If you are looking for something particular you can search for the
> object here:
> http://www.cisco.com/pcgi-bin/Support/Mibbrowser/unity.pl?tab=3
>
> Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
>
> -----Original Message-----
> From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
> Brian McGahan
> Sent: Sunday, July 13, 2003 7:38 PM
> To: 'Emad '; ccielab@groupstudy.com
> Subject: RE: MIB values
>
> Cisco does maintain a list of the supported MIB values on a per
> platform basis, but it's a little hard to navigate. See the following
> link for more info:
>
> http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml
>
>
> MIB values are platform specific. In my experience, the easiest
> way to find a specific MIB value is to just snmpwalk the device in
> question. 'Snmpwalk'ing a device means to send a series of getnext
> requests to the device, which results in showing every MIB value
> supported on that device and the corresponding value. 'snmpwalk' can be
> run from the *nix command line, or from management software such as
> solarwinds, etc.
>
> Do a google search for snmpwalk for more info:
>
> http://www.google.com/search?hl=en&lr=&ie=UTF-8&oe=UTF-8&q=snmpwalk&spel
> l=1
>
>
>
> HTH,
>
> Brian McGahan, CCIE #8593
> Director of Design and Implementation
> brian@cyscoexpert.com
>
> CyscoExpert Corporation
> Internetwork Consulting & Training
> Toll Free: 866.CyscoXP
> Fax: 847.674.2625
>
>
> > -----Original Message-----
> > From: Emad [mailto:emad@zakq8.com]
> > Sent: Sunday, July 13, 2003 9:51 AM
> > To: ba@cyscoexpert.com
> > Subject: MIB values
> > Importance: High
> >
> > Hi Brian,
> > Sorry for sending offline but I consider u the guru of this group and
> > nobody answered me about this question till now,
> >
> > RMON is very straight forward , but I don't have questions about it
> > except Jeff doyle and I found that it asks to make RMON trap for
> certain
> > MIB like interface CRC error , how can I know all the MIBs value , is
> it
> > a must to memorize all or it will give me in the lab?
> >
> > Thanx in advance
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
>
>
> _______________________________________________________________________
> You are subscribed to the GroupStudy.com CCIE R&S Discussion Group.
>
> Subscription information may be found at:
> http://www.groupstudy.com/list/CCIELab.html
This archive was generated by hypermail 2.1.4 : Wed Aug 06 2003 - 06:52:40 GMT-3