From: John Humphrey (john.humphrey@txkisd.net)
Date: Sat Jun 28 2003 - 23:51:59 GMT-3
I have an MC3810 with two T1 cards in it. One card (t1 0) allows me to
configure channel-groups just fine. The second card, however, doesn't
give me the option to setup any channel groups. I've tried two different
IOS releases (12.1 and 12.2). This used to work just fine, now all the
sudden it stopped. Any thoughts? I'll attach the relevant portions of the
config below:
System image file is "flash:mc3810-i-mz.122-1d.bin"
cisco MC3810 (MPC860) processor (revision 10.01) with 28672K/4096K bytes
of memory.
Processor board ID 14775434
PPC860 PowerQUICC, partnum 0x0000, version C01(0x0031)
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
MC3810 SCB board (v16.B0)
1 Multiflex T1(slot 3) RJ45 interface(v02.C0)
1 Multiflex T1(slot 4) RJ45 interface(v03.A0)
1 Ethernet/IEEE 802.3 interface(s)
1 Serial network interface(s)
2 Serial(sync/async) network interface(s)
2 Channelized T1/PRI port(s)
256K bytes of non-volatile configuration memory.
8192K bytes of processor board System flash (AMD29F016)
Configuration register is 0x2102
All T1 0 config options:
R2(config-controller)#?
Controller configuration commands:
alarm-trigger ds0 alarm aggregation
cablelength Specify the cable length for a DS1 link
channel-group Specify the timeslots to channel-group mapping for an
interface
clock Specify the clock source for a DS1 link
default Set a command to its defaults
description Controller specific description
ds0 ds0 commands
ds0-group Replacement of cas-group. Configure group of timeslots
to a particular signalling type
exit Exit from controller configuration mode
fdl Specify the FDL standard for a DS1 data link
framing Specify the type of Framing on a DS1 link
help Description of the interactive help system
linecode Specify the line encoding method for a DS1 link
loop-detect Loopback up or down detection
loopback Put the entire T1 line into loopback
mode Configure the controller mode
no Negate a command or set its defaults
pri-group Configure the specified timeslots for PRI
shutdown Shut down a DS1 link (send Blue Alarm)
tdm-group Configure DS0 group for TDM
All T1 1 config options:
R2(config-controller)#?
Controller configuration commands:
alarm-trigger ds0 alarm aggregation
cablelength Specify the cable length for a DS1 link
clock Specify the clock source for a DS1 link
default Set a command to its defaults
description Controller specific description
ds0 ds0 commands
ds0-group Replacement of cas-group. Configure group of timeslots
to a particular signalling type
exit Exit from controller configuration mode
fdl Specify the FDL standard for a DS1 data link
framing Specify the type of Framing on a DS1 link
help Description of the interactive help system
linecode Specify the line encoding method for a DS1 link
loop-detect Loopback up or down detection
loopback Put the entire T1 line into loopback
mode Configure the controller mode
no Negate a command or set its defaults
pri-group Configure the specified timeslots for PRI
shutdown Shut down a DS1 link (send Blue Alarm)
tdm-group Configure DS0 group for TDM
Thanks in advance!
jh
This archive was generated by hypermail 2.1.4 : Fri Jul 04 2003 - 11:11:14 GMT-3