From: Brian Dennis (brian@labforge.com)
Date: Wed May 28 2003 - 05:01:29 GMT-3
Remove pap authentication and then try to call. Think about it like
this, if you can't make a simple call across why have it on. Actually
you could just remove PPP all together. As a side note you need the "ppp
pap sent-username" interface command on for PAP authentication. Even if
your ISDN switch worked you wouldn't be able to authenticate with PAP
using your config.
You should be able to test with just this config:
R5:
interface BRI1/0
isdn switch-type basic-ni
isdn spid1 5101 5001
isdn spid2 5102 5002
R6:
interface BRI0
isdn switch-type basic-ni
isdn spid1 6101 6001
isdn spid2 6102 6002
First do a "show isdn status" and make sure you have multiple frames
established along with spidX send, spidX valid. Then do an "isdn call
interface bri1/0 6001" from R5. You should see it connect to R6 if the
ISDN switch is working. You could also try it from R6 (isdn call
interface bri0 5001)
Brian Dennis, CCIE #2210 (R&S/ISP-Dial/Security)
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of
Szeto Jeff
Sent: Tuesday, May 27, 2003 11:28 PM
To: ccielab@groupstudy.com
Subject: OT: basic isdn problem
Hi,
Please help.
R5:
username R6 password 0 cisco
interface BRI1/0
ip address 1.1.1.5 255.255.255.0
encapsulation ppp
dialer map ip 1.1.1.6 name R6 broadcast 6001
dialer map ip 1.1.1.6 name R6 broadcast 6002
dialer-group 1
isdn switch-type basic-ni
isdn spid1 5101 5001
isdn spid2 5102 5002
ppp authentication pap
dialer-list 1 protocol ip permit
R6
username R5 password 0 cisco
interface BRI0
ip address 1.1.1.6 255.255.255.0
encapsulation ppp
dialer map ip 1.1.1.5 name R5 broadcast 5001
dialer map ip 1.1.1.5 name R5 broadcast 5002
dialer-group 1
isdn switch-type basic-ni
isdn spid1 6101 6001
isdn spid2 6102 6002
ppp authentication pap
dialer-list 1 protocol ip permit
The isdn switch is a nortel pbx.
Here is the debug dialer message on R5:
R5#ping 1.1.1.6
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 1.1.1.6, timeout is 2 seconds:
00:14:47: BR1/0 DDR: Dialing cause ip (s=1.1.1.5, d=1.1.1.6)
00:14:47: BR1/0 DDR: Attempting to dial 6001
00:14:47: ISDN BR1/0: Outgoing call id = 0x8006, dsl 8
00:14:47: ISDN BR1/0: Event: Call to 6001 at 64 Kb/s
00:14:47: ISDN BR1/0: process_bri_call(): call id 0x8006, called_number
6001, sp
eed 64, call type DATA
00:14:47: CCBRI_Go Fr Host InPkgInfo (Len=19) :
00:14:47: 1 8 1 80 6 0 4 2 88 90 18 1 83 2C 4 36 30 30 31
00:14:47:
00:14:47: CC_CHAN_GetIdleChanbri: dsl 8
00:14:47: Found idle channel B1
00:14:47: CCBRI_Go Fr L3 pkt (Len=7) :
00:14:47: 2 1 5 98 18 1 89
00:14:47:
00:14:47: ISDN BR1/0: LIF_EVENT: ces/callid 1/0x8006
HOST_PROCEEDING.....
Success rate is 0 percent (0/5)
R4-3640#
00:15:09: CCBRI_Go Fr L3 pkt (Len=11) :
00:15:09: 45 1 5 96 8 2 81 90 34 1 3F
00:15:09:
00:15:09: ISDN BR1/0: LIF_EVENT: ces/callid 1/0x8006 HOST_DISCONNECT
00:15:09: ISDN BR1/0: Event: Call to 6001 was hung up.
00:15:09: ISDN BR1/0: process_disc_ack(): call id 0x8006, ces 1, call
type
DATA
cause 0x0
00:15:09: ISDN: get_isdn_service_state(): idb 0x61ECB0B8 bchan 2 is_isdn
1
Not a
Pri
00:15:09: BRI1/0: wait for isdn carrier timeout, call id=0x8006
00:15:09: BR1/0 DDR: Attempting to dial 6002
00:15:09: ISDN BR1/0: Outgoing call id = 0x8007, dsl 8
00:15:09: CCBRI_Go Fr Host InPkgInfo (Len=10) :
00:15:09: 6 8 1 80 6 0 8 2 0 8
00:15:09:
00:15:09: ISDN BR1/0: Event: Call to 6002 at 64 Kb/s
00:15:09: ISDN BR1/0: process_bri_call(): call id 0x8007, called_number
6002, sp
eed 64, call type DATA
00:15:09: CCBRI_Go Fr Host InPkgInfo (Len=19) :
00:15:09: 1 8 1 80 7 0 4 2 88 90 18 1 83 2C 4 36 30 30 32
00:15:09:
00:15:09: CC_CHAN_GetIdleChanbri: dsl 8
00:15:09: Found idle channel B2
00:15:09: CCBRI_Go Fr L3 pkt (Len=7) :
00:15:09: 5A 1 5 99 34 1 3F
00:15:09:
00:15:09: ISDN BR1/0: LIF_EVENT: ces/callid 1/0x8006 HOST_DISCONNECT_ACK
00:15:09: ISDN: get_isdn_service_state(): idb 0x61ECB0B8 bchan 2 is_isdn
1
Not a
Pri
00:15:09: ISDN BR1/0: HOST_DISCONNECT_ACK: call type is DATA
00:15:09: CCBRI_Go Fr L3 pkt (Len=7) :
00:15:09: 2 1 6 98 18 1 89
00:15:09:
00:15:09: ISDN BR1/0: LIF_EVENT: ces/callid 1/0x8007 HOST_PROCEEDING
00:15:31: CCBRI_Go Fr L3 pkt (Len=11) :
00:15:31: 45 1 6 96 8 2 81 90 34 1 3F
00:15:31:
00:15:31: ISDN BR1/0: LIF_EVENT: ces/callid 1/0x8007 HOST_DISCONNECT
00:15:31: ISDN BR1/0: Event: Call to 6002 was hung up.
00:15:31: ISDN BR1/0: process_disc_ack(): call id 0x8007, ces 1, call
type
DATA
cause 0x0
00:15:31: ISDN: get_isdn_service_state(): idb 0x61ECB0B8 bchan 2 is_isdn
1
Not a
Pri
00:15:31: BRI1/0: wait for isdn carrier timeout, call id=0x8007
00:15:31: CCBRI_Go Fr Host InPkgInfo (Len=10) :
00:15:31: 6 8 1 80 7 0 8 2 0 8
00:15:31:
00:15:31: CCBRI_Go Fr L3 pkt (Len=7) :
00:15:31: 5A 1 6 99 34 1 3F
00:15:31:
00:15:31: ISDN BR1/0: LIF_EVENT: ces/callid 1/0x8007 HOST_DISCONNECT_ACK
00:15:31: ISDN: get_isdn_service_state(): idb 0x61ECB0B8 bchan 2 is_isdn
1
Not a
Pri
00:15:31: ISDN BR1/0: HOST_DISCONNECT_ACK: call type is DATA
I think the second last message is something related to the problem. But
I
am not familiar with the pbx system, so I cannot fix it.
Any suggestion is appreciated.
Thank you in advance.
Regards,
Jeff
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2003 - 15:13:49 GMT-3