From: Danny.Andaluz@triaton-na.com
Date: Wed May 14 2003 - 12:58:33 GMT-3
Actually the default is 120 seconds. See below:
interface BRI0
ip address xx.xx.xx.xx xx.xx.xx.xx
encapsulation ppp
ip ospf message-digest-key 1 md5 cisco
ip ospf demand-circuit
dialer map ip xx.xx.xxx.xx name xx broadcast xxxx
dialer load-threshold 1 outbound
dialer-group 1
isdn switch-type basic-ni
isdn spid1 000653801
no peer neighbor-route
ppp chap hostname xxxxxx
ppp chap password 7 xxxxxxx
xx#sh dialer
BRI0 - dialer type = ISDN
Dial String Successes Failures Last DNIS Last status
6539 38 39 1d00h successful
0 incoming call(s) have been screened.
0 incoming call(s) rejected for callback.
BRI0:1 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is shutdown
BRI0:2 - dialer type = ISDN
Idle timer (120 secs), Fast idle timer (20 secs)
Wait for carrier (30 secs), Re-enable (15 secs)
Dialer state is shutdown
xx#sh ver
Cisco Internetwork Operating System Software
IOS (tm) 2500 Software (C2500-JOS56I-L), Version 12.1(19), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Tue 04-Mar-03 14:46 by kellythw
Image text-base: 0x0307ED04, data-base: 0x00001000
ROM: System Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
BOOTLDR: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE SOFTWARE (fc1)
r5 uptime is 2 days, 1 hour, 32 minutes
System returned to ROM by reload
System image file is "flash:/c2500-jos56i-l.121-19.bin"
cisco 2500 (68030) processor (revision F) with 16384K/2048K bytes of memory.
Processor board ID 04796630, with hardware revision 00000000
Bridging software.
X.25 software, Version 3.0.0.
SuperLAT software (copyright 1990 by Meridian Technology Corp).
TN3270 Emulation software.
Basic Rate ISDN software, Version 1.1.
1 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 ISDN Basic Rate interface(s)
32K bytes of non-volatile configuration memory.
16384K bytes of processor board System flash (Read ONLY)
Configuration register is 0x2102
-----Original Message-----
From: Tony Schaffran [mailto:tschaffran@cconlinelabs.com]
Sent: Wednesday, May 14, 2003 11:48 AM
To: 'John Matijevic'; Coley, Efrem D. ,Triaton/NA; jpark@wams.com; ccielab@groupstudy.com
Subject: RE: ISDN doesn't stay up more than a second
Still without that command, the default is 90 seconds. That command will not fix his problem.
Tony Schaffran
Network Analyst
CCIE #11071
CCNP, CCNA, CCDA
NNCDS, NNCSS, CNE, MCSE
http://www.cconlinelabs.com/
Your #1 choice for online cisco rack rentals.
-----Original Message-----
From: nobody@groupstudy.com [mailto:nobody@groupstudy.com] On Behalf Of John Matijevic
Sent: Wednesday, May 14, 2003 7:44 AM
To: Efrem.Coley@triaton-na.com; jpark@wams.com; ccielab@groupstudy.com
Subject: Re: ISDN doesn't stay up more than a second
I believe the command your looking for is:
dialer idle-timeout 0
sincerely,
John Matijevic
----- Original Message -----
From: <Efrem.Coley@triaton-na.com>
To: <jpark@wams.com>; <ccielab@groupstudy.com>
Sent: Wednesday, May 14, 2003 9:01 AM
Subject: RE: ISDN doesn't stay up more than a second
> Do you have usernames configured on both routers for chap
> authentication? Efrem
>
> -----Original Message-----
> From: Jeongwoo Park [mailto:jpark@wams.com]
> Sent: Wednesday, May 14, 2003 7:35 AM
> To: 'ccielab@groupstudy.com'
> Subject: ISDN doesn't stay up more than a second
>
> Hi,
> The first time to play with isdn with my own equipments.
> The isdn topology.
> r2----ISDN----r1
> I just want to make it stay up.
>
> r1;
> interface BRI0/0
> ip address 172.16.12.1 255.255.255.0
> encapsulation ppp
> dialer map ip 172.16.12.2 name r2 broadcast 8358662 dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 0835866101 8358661
> isdn spid2 0835866301 8358663
> no peer neighbor-route
> ppp authentication chap
>
> !
> dialer-list 1 protocol ip permit
>
> r2;
> interface BRI0/0
> ip address 172.16.12.2 255.255.255.0
> encapsulation ppp
> dialer map ip 172.16.12.1 name r1 broadcast 8358661 dialer-group 1
> isdn switch-type basic-ni
> isdn spid1 0835866201 8358662
> isdn spid2 0835866401 8358664
> no peer neighbor-route
> ppp authentication chap
> !
> dialer-list 1 protocol ip permit
>
> Here is output of deb isdn event, deb isdn q931 when I send ping
> traffic. r2#ping 172.16.12.1
>
> Type escape sequence to abort.
> Sending 5, 100-byte ICMP Echos to 172.16.12.1, timeout is 2 seconds:
>
> 1d03h: ISDN BR0/0: Outgoing call id = 0x801F, dsl 0
> 1d03h: ISDN BR0/0: Event: Call to 8358661 at 64 Kb/s
> 1d03h: ISDN BR0/0: process_bri_call(): call id 0x801F, called_number
> 8358661, speed 64, call type DATA
> 1d03h: CC_CHAN_GetIdleChanbri: dsl 0
> 1d03h: Found idle channel B1
> 1d03h: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x1F
> 1d03h: Bearer Capability i = 0x8890
> 1d03h: Channel ID i = 0x83
> 1d03h: Keypad Facility i = '8358661'
> 1d03h: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref = 0x9F
> 1d03h: Channel ID i = 0x89
> 1d03h: Locking Shift to Codeset 5
> 1d03h: Codeset 5 IE 0x2A i = 0x809402, '`=', 0x8307, '8358661',
> 0x8E0B20, 'Teltone', 0x20, '1', 0x20
> 1d03h: ISDN BR0/0: received HOST_PROCEEDING call_id 0x801F
> 1d03h: ISDN BR0/0: RX <- CONNECT pd = 8 callref = 0x9F
> 1d03h: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref = 0x1F
> 1d03h: ISDN BR0/0: received HOST_CONNECT call_id 0x801F
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> 1d03h: ISDN BR0/0: Event: Connected to 8358661 on B1 at 64 Kb/s.
> 1d03h: ISDN BR0/0: RX <- DISCONNECT pd = 8 callref = 0x9F
> 1d03h: Cause i = 0x8290 - Normal call clearing
> 1d03h: Signal i = 0x3F - Tones off
> 1d03h: ISDN BR0/0: TX -> RELEASE pd = 8 callref = 0x1F
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT call_id 0x801F
> 1d03h: ISDN BR0/0: Event: Call to <unknown> was hung up.
> 1d03h: ISDN BR0/0: process_disc_ack(): call id 0x801F, ces 1, call
> type
DATA
> 1d03h: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 8358661
> 1d03h: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
> 8358661 , call lasted 1 seconds
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
> 1d03h: ISDN BR0/0: RX <- RELEASE_COMP pd = 8 callref = 0x9F
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT_ACK call_id 0x801F
> 1d03h: ISDN BR0/0: HOST_DISCONNECT_ACK: call type is DATA
> 1d03h: ISDN BR0/0: Outgoing call id = 0x8020, dsl 0
> 1d03h: ISDN BR0/0: Event: Call to 8358661 at 64 Kb/s
> 1d03h: ISDN BR0/0: process_bri_call(): call id 0x8020, called_number
> 8358661, speed 64, call type DATA
> 1d03h: CC_CHAN_GetIdleChanbri: dsl 0
> 1d03h: Found idle channel B1
> 1d03h: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x20
> 1d03h: Bearer Capability i = 0x8890
> 1d03h: Channel ID i = 0x83
> 1d03h: Keypad Facility i = '8358661'
> 1d03h: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref = 0xA0
> 1d03h: Channel ID i = 0x89
> 1d03h: Locking Shift to Codeset 5
> 1d03h: Codeset 5 IE 0x2A i = 0x809402, '`=', 0x8307, '8358661',
> 0x8E0B20, 'Teltone', 0x20, '1', 0x20
> 1d03h: ISDN BR0/0: received HOST_PROCEEDING call_id 0x8020
> 1d03h: ISDN BR0/0: RX <- CONNECT pd = 8 callref = 0xA0
> 1d03h: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref = 0x20
> 1d03h: ISDN BR0/0: received HOST_CONNECT call_id 0x8020
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> 1d03h: ISDN BR0/0: E.vent: Connected to 8358661 on B1 at 64 Kb/s
> 1d03h: ISDN BR0/0: RX <- DISCONNECT pd = 8 callref = 0xA0
> 1d03h: Cause i = 0x8290 - Normal call clearing
> 1d03h: Signal i = 0x3F - Tones off
> 1d03h: ISDN BR0/0: TX -> RELEASE pd = 8 callref = 0x20
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT call_id 0x8020
> 1d03h: ISDN BR0/0: Event: Call to <unknown> was hung up.
> 1d03h: ISDN BR0/0: process_disc_ack(): call id 0x8020, ces 1, call
> type
DATA
> 1d03h: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 8358661
> 1d03h: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
> 8358661 , call lasted 1 seconds
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
> 1d03h: ISDN BR0/0: RX <- RELEASE_COMP pd = 8 callref = 0xA0
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT_ACK call_id 0x8020
> 1d03h: ISDN BR0/0: HOST_DISCONNECT_ACK: call type is DATA
> 1d03h: ISDN BR0/0: Outgoing call id = 0x8021, dsl 0
> 1d03h: ISDN BR0/0: Event: Call to 8358661 at 64 Kb/s
> 1d03h: ISDN BR0/0: process_bri_call(): call id 0x8021, called_number
> 8358661, speed 64, call type DATA
> 1d03h: CC_CHAN_GetIdleChanbri: dsl 0
> 1d03h: Found idle channel B1
> 1d03h: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x21
> 1d03h: Bearer Capability i = 0x8890
> 1d03h: Channel ID i = 0x83
> 1d03h: Keypad Facility i = '8358661'
> 1d03h: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref = 0xA1
> 1d03h: Channel ID i = 0x89
> 1d03h: Locking Shift to Codeset 5
> 1d03h: Codeset 5 IE 0x2A i = 0x809402, '`=', 0x8307, '8358661',
> 0x8E0B20, 'Teltone', 0x20, '1', 0x20
> 1d03h: ISDN BR0/0: received HOST_PROCEEDING call_id 0x8021
> 1d03h: ISDN BR0/0: RX <- CONNECT pd = 8 callref = 0xA1
> 1d03h: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref = .0x21
> 1d03h: ISDN BR0/0: received HOST_CONNECT call_id 0x8021
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> 1d03h: ISDN BR0/0: Event: Connected to 8358661 on B1 at 64 Kb/s
> 1d03h: ISDN BR0/0: RX <- DISCONNECT pd = 8 callref = 0xA1
> 1d03h: Cause i = 0x8290 - Normal call clearing
> 1d03h: Signal i = 0x3F - Tones off
> 1d03h: ISDN BR0/0: TX -> RELEASE pd = 8 callref = 0x21
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT call_id 0x8021
> 1d03h: ISDN BR0/0: Event: Call to <unknown> was hung up.
> 1d03h: ISDN BR0/0: process_disc_ack(): call id 0x8021, ces 1, call
> type
DATA
> 1d03h: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 8358661
> 1d03h: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
> 8358661 , call lasted 1 seconds
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
> 1d03h: ISDN BR0/0: RX <- RELEASE_COMP pd = 8 callref = 0xA1
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT_ACK call_id 0x8021
> 1d03h: ISDN BR0/0: HOST_DISCONNECT_ACK: call type is DATA
> 1d03h: ISDN BR0/0: Outgoing call id = 0x8022, dsl 0
> 1d03h: ISDN BR0/0: Event: Call to 8358661 at 64 Kb/s
> 1d03h: ISDN BR0/0: process_bri_call(): call id 0x8022, called_number
> 8358661, speed 64, call type DATA
> 1d03h: CC_CHAN_GetIdleChanbri: dsl 0
> 1d03h: Found idle channel B1
> 1d03h: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x22
> 1d03h: Bearer Capability i = 0x8890
> 1d03h: Channel ID i = 0x83
> 1d03h: Keypad Facility i = '8358661'
> 1d03h: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref = 0xA2
> 1d03h: Channel ID i = 0x89
> 1d03h: Locking Shift to Codeset 5
> 1d03h: Codeset 5 IE 0x2A i = 0x809402, '`=', 0x8307, '8358661',
> 0x8E0B20, 'Teltone', 0x20, '1', 0x20
> 1d03h: ISDN. BR0/0: received HOST_PROCEEDING call_id 0x8022
> 1d03h: ISDN BR0/0: RX <- CONNECT pd = 8 callref = 0xA2
> 1d03h: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref = 0x22
> 1d03h: ISDN BR0/0: received HOST_CONNECT call_id 0x8022
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> 1d03h: ISDN BR0/0: Event: Connected to 8358661 on B1 at 64 Kb/s
> 1d03h: ISDN BR0/0: RX <- DISCONNECT pd = 8 callref = 0xA2
> 1d03h: Cause i = 0x8290 - Normal call clearing
> 1d03h: Signal i = 0x3F - Tones off
> 1d03h: ISDN BR0/0: TX -> RELEASE pd = 8 callref = 0x22
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT call_id 0x8022
> 1d03h: ISDN BR0/0: Event: Call to <unknown> was hung up.
> 1d03h: ISDN BR0/0: process_disc_ack(): call id 0x8022, ces 1, call
> type
DATA
> 1d03h: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 8358661
> 1d03h: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
> 8358661 , call lasted 1 seconds
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
> 1d03h: ISDN BR0/0: RX <- RELEASE_COMP pd = 8 callref = 0xA2
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT_ACK call_id 0x8022
> 1d03h: ISDN BR0/0: HOST_DISCONNECT_ACK: call type is DATA
> 1d03h: ISDN BR0/0: Outgoing call id = 0x8023, dsl 0
> 1d03h: ISDN BR0/0: Event: Call to 8358661 at 64 Kb/s
> 1d03h: ISDN BR0/0: process_bri_call(): call id 0x8023, called_number
> 8358661, speed 64, call type DATA
> 1d03h: CC_CHAN_GetIdleChanbri: dsl 0
> 1d03h: Found idle channel B1
> 1d03h: ISDN BR0/0: TX -> SETUP pd = 8 callref = 0x23
> 1d03h: Bearer Capability i = 0x8890
> 1d03h: Channel ID i = 0x83
> 1d03h: Keypad Facility i = '8358661'
> 1d03h: ISDN BR0/0: RX <- CALL_PROC pd = 8 callref = 0xA3
> 1d03h: Channel ID i = 0x89
> 1d.
> Success rate is 0 percent (0/5)
> r2#03h: Locking Shift to Codeset 5
> 1d03h: Codeset 5 IE 0x2A i = 0x809402, '`=', 0x8307, '8358661',
> 0x8E0B20, 'Teltone', 0x20, '1', 0x20
> 1d03h: ISDN BR0/0: received HOST_PROCEEDING call_id 0x8023
> 1d03h: ISDN BR0/0: RX <- CONNECT pd = 8 callref = 0xA3
> 1d03h: ISDN BR0/0: TX -> CONNECT_ACK pd = 8 callref = 0x23
> 1d03h: ISDN BR0/0: received HOST_CONNECT call_id 0x8023
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to up
> 1d03h: ISDN BR0/0: Event: Connected to 8358661 on B1 at 64 Kb/s
> 1d03h: ISDN BR0/0: RX <- DISCONNECT pd = 8 callref = 0xA3
> 1d03h: Cause i = 0x8290 - Normal call clearing
> 1d03h: Signal i = 0x3F - Tones off
> 1d03h: ISDN BR0/0: TX -> RELEASE pd = 8 callref = 0x23
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT call_id 0x8023
> 1d03h: ISDN BR0/0: Event: Call to <unknown> was hung up.
> 1d03h: ISDN BR0/0: process_disc_ack(): call id 0x8023, ces 1, call
> type
DATA
> 1d03h: %ISDN-6-CONNECT: Interface BRI0/0:1 is now connected to 8358661
> 1d03h: %ISDN-6-DISCONNECT: Interface BRI0/0:1 disconnected from
> 8358661 , call lasted 1 seconds
> 1d03h: %LINK-3-UPDOWN: Interface BRI0/0:1, changed state to down
> 1d03h: ISDN BR0/0: RX <- RELEASE_COMP pd = 8 callref = 0xA3
> 1d03h: ISDN BR0/0: received HOST_DISCONNECT_ACK call_id 0x8023
> 1d03h: ISDN BR0/0: HOST_DISCONNECT_ACK: call type is DATA
> r2#
This archive was generated by hypermail 2.1.4 : Mon Jun 02 2003 - 15:13:42 GMT-3